CyberPower CPS700AVR User Manual Download Page 11

 

CPS700AVR  

Guaranteed Uninterruptible Power System 

 
 
EXPECTED RUNTIME IN MINUTES 

 

 

 

 

 

 

 

Example Systems 

 

 

 

 
 
 
 
 
 

 

REPLACING THE BATTERY 

 

CAUTION!  

Read and follow the 

IMPORTANT SAFETY INSTRUCTIONS

 before servicing the battery.  

Service the battery under the supervision of 

personnel knowledgeable of batteries and their precautions. 
 

CAUTION!  

Use only the specified type of battery.  

See your dealer for replacement batteries. 

 

CAUTION!  

The battery may present risk of electrical shock.  Do not dispose of battery in a fire, as it may explode.  Follow all local ordinances regarding 

proper disposal of batteries. 
 

CAUTION!

  

Do not open or mutilate the batteries.  Released electrolyte is harmful to skin and eyes and may be toxic. 

 

CAUTION!

  

A battery can present a high risk of short circuit current and electrical shock.  Take the following precautions before replacing the battery: 

 

1. 

Remove all watches, rings or other metal objects. 

2. 

Only use tools with insulated handles. 

3. 

Do not lay tools or metal parts on top of battery or any terminals. 

4. 

Wear rubber gloves and boots. 

5. 

Determine if the battery is inadvertently grounded.  If inadvertently grounded, remove source of ground.  

CONTACT WITH GROUNDED 

BATTERY CAN RESULT IN ELECTRICAL SHOCK!  

The likelihood of such shock will be reduced if such grounds are removed during installation 

and maintenance (applicable to a UPS and a remote battery supply not having a grounded circuit). 

 

TO REPLACE THE BATTERY 

 

1. 

Turn off and unplug all connected equipment. 

2. 

Turn the UPS off and unplug it from the AC power source. 

3. 

Turn the UPS upside down. 

4. 

Remove the 4 retaining screws. 

5. 

Turn the UPS right side up and remove the cover. 

6. 

Remove the battery from the compartment. 

7. 

Disconnect the battery wires from the battery. 

8. 

Install the replacement battery by connecting the 

red wire to the positive (+) terminal of the battery

 and connecting the 

black wire to the 

negative (-) terminal of the battery.

 

9. 

Slide the battery back into the compartment. 

10.  Replace the outlet cover and the 6 retaining screws. 
11.  Recharge the unit for 4 – 8 hours to ensure the UPS performs expected runtime. 
 

REMINDER:  

Batteries are consider 

HAZARDOUS WASTE

 and must be disposed of properly.  Contact your local government for more information 

about proper disposal and recycling of batteries. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Load (Watts) 

CPS 700AVR™ Model Runtime 

75 50 

125 30 
150 20 
200 17 
250 12 
300 4 
350 2 

Desktop PC with 15” Monitor 

38 - 45 

Desktop PC with 17” Monitor 

28 - 36 

Desktop PC with 21” Monitor 

24 - 28 

Tower PC with 21” Monitor 

20 - 24 

Summary of Contents for CPS700AVR
















Reviews: