background image

Please visit www.CyberPowerSystems.com for a copy of the Limited Warranty and Connected 

Equipment Guarantee. 

Where Can I Get More Information?  

     

The application of the United Nations Convention of Contracts for the International Sale of  

Goods is expressly excluded. CyberPower is the warrantor under this Limited Warranty.  

For further information please feel free to contact CyberPower at: 

Cyber Power Systems (USA), Inc. 4241 12th Ave E., STE 400, Shakopee, MN 55379;  

call us at 

(877) 297-6937

; or submit a web ticket online at 

cyberpowersystems.com/support

.

Cyber Power Systems (USA), Inc. encourages environmentally sound methods for disposal  

and recycling of its UPS products. Please dispose and/or recycle your UPS and batteries in  

accordance to the local regulations of your state.

WARNING:

 This product can expose you to chemicals including bisphenol A (BPA) and styrene, which is known to the  

State of California to cause reproductive harm and cancer.  For more information, go to www.P65Warnings.ca.gov. 

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device 

may not cause harmful interference, and (2) this device must accept any interference received, including interference 

that may cause undesired operation.  

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance 

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference 

will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more 

of the following measures:  

- Reorient or relocate the receiving antenna.  

- Increase the separation between the equipment and receiver.  

- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.  

- Consult the dealer or an experienced radio/TV technician for help.  

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void  

the user’s authority to operate the equipment.
 

Canadian Compliance Statement  

CAN ICES-3 (B)/NMB-3(B)

LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE

FCC COMPLIANCE STATEMENT

© 2021 CyberPower Systems (USA), Inc. PowerPanel® Personal is a trademark of Cyber Power Systems(USA) Inc.

All rights reserved. All other trademarks are the property of their respective owners.

Summary of Contents for CP1350PFCLCD











Reviews: