manualshive.com logo in svg

Cybernet iONE-GX45 Series, User Manual, Page: 23 / 32

Share
Download
Cybernet iONE-GX45 Series User Manual Download Page 23

 

Cybernet iONE-GX45                                                                         eWaste SOP USA 

Page 17 

Installing the Hard Disk Drive 

 

1.  Unscrew the four screws on the Optical Disk  
     Drive frame (2 shown circled, 2 on opposite  
     side) and remove the frame and  
     disconnect the SATA cable from the  
     mainboard and set aside in order to gain  
     access to the Hard Disk Drive slot. 

 
 
 
 

Optical Disk Drive Frame Screws 

 

 

 
 

2.  Slide the hard disk drive into the frame and  
     line up the two screw holes accordingly.   
     Secure the two screws on the Hard Disk  
     Drive. 
     Connect the SATA cable to the mainboard. 

 

SATA Cable

 

 

 
 
 
 

 
 

 

3.  Connect the other end of the SATA/Power  
     cable to the Hard Disk Drive as shown. 
 
4.  Replace the Optical Disk Drive securing the 
four screws (two screws on the top, two screws 
on the side) to secure the HDD and complete 
the installation. 

 
 
 
 

 

Power Cable    SATA Cable 

 
 

 
 

 

 

Summary of Contents for iONE-GX45 Series

































Reviews:

No comments