background image

 

ii 

 

Safety Instructions 
 

1. 

Always read the safety instructions carefully. 

2. 

Keep this equipment away from humidity. 

3. 

Lay this equipment on a reliable flat surface before setting it up. 

4. 

The openings on the enclosure are for air convection hence protect the 
equipment from overheating. DO NOT COVER THE OPENINGS. 

5. 

Confirm the voltage of the power source and adjust accordingly to 110/220V 
before connecting the equipment to the power inlet. 

6. 

Place the power cord in such a way that it cannot be stepped on.  Do not 
place anything over the power cord. 

7. 

Always unplug the Power Cord before inserting any add-on card or module. 

8. 

All cautions and warnings on the equipment should be noted. 

9. 

Never pour any liquid into the opening.   This will cause damage and/or electrical 
shock. 

10. 

Do not disable the protective grounding pin from the plug.  The equipment must be 
connected to a grounded main socket/outlet. 

11. 

The Optical Storage devices are classified as Class 1 Laser products.  Use of 
controls or adjustments or performance of procedures other than those specified is 
prohibited. 

12. 

Do not touch the Laser lens inside the optical storage drive. 

13. 

When installing the coaxial cable to the TV Tuner, it is necessary to ensure that the 
metal shield is reliably connected to a protective earthing system of the building. 
Cable distribution systems should be grounded (earthed) in accordance with 
ANSI/NF PA 70, the National Electrical Code (NEC ), in particular, Section 820.93, 
Grounding of Outer Conductive Shield of a Coaxial Cable. 

14. 

If any of the following situations arise, have the equipment checked by authorized 
service personnel: 

  The power cord or plug is damaged. 

  Liquid has penetrated into the equipment. 

  The equipment has been exposed to moisture. 

  The equipment has not worked well or you cannot get it working according to 

the User's Guide. 

  The equipment has been dropped and damaged. 

  The equipment has obvious signs of breakage. 

15. 

Do not attempt to remove or upgrade any component by yourself, any installation or 
modification should be conducted by service personnel. 

 
 
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONDITIONED ENVIRONMENT WITH A 
STORAGE TEMPERATURE ABOVE 50° C (122°F).   IT MAY DAMAGE THE 
EQUIPMENT. 
 
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the 
same or equivalent type recommended by the manufacturer.  

Summary of Contents for H6 i-One Series































Reviews: