manualshive.com logo in svg

CyberData RAL 9003, Operation Manual, Page: 48 / 126

Share
Download
CyberData RAL 9003 Operation Manual Download Page 48

 

Installing the Singlewire InformaCast Talk-Back Speaker

Device Configuration

Operations Guide

931260A

CyberData Corporation

41

3. On the 

Home 

page, review the setup details and navigation buttons described in 

Table 2-6

.

Note

The question mark icon (

) in the following table shows which web page items will be defined 

after the 

Toggle Help

 button is pressed

.

Table 2-6. Home Page Overview  

Web Page Item

Description

Admin Settings

Username 

The username to access the web interface. Enter up to 25 characters.

Password 

The password to access the web interface. Enter up to 25 characters.

Confirm Password 

Confirm the web interface password.

Current Status

Serial Number

Shows the device serial number.

Mac Address

Shows the device Mac address.

Firmware Version

Shows the current firmware version.

IP Addressing

Shows the current IP addressing setting (

DHCP

 or 

static

).

IP Address

Shows the current IP address.

Subnet Mask

Shows the current subnet mask address.

Default Gateway

Shows the current default gateway address.

DNS Server 1

Shows the current DNS Server 1 address.

DNS Server 2

Shows the current DNS Server 2 address.

SIP Mode

Shows the current status of the SIP mode.

Multicast Mode

Shows the current status of the Multicast mode.

Event Reporting

Shows the current status of the Event Reporting mode.

Nightringer

Shows the current status of the Nightringer mode.

Primary SIP Server

Shows the current status of the Primary SIP Server.

Backup Server 1

Shows the current status of Backup Server 1.

Backup Server 2

Shows the current status of Backup Server 2.

Nightringer Server

Shows the current status of Nightringer Server.

Summary of Contents for RAL 9003































































































































Reviews:

No comments