manualshive.com logo in svg

Cyber Power Mini Central CPSPV30000ETL Series, User Manual

Share
Download
Cyber Power Mini Central CPSPV30000ETL Series User Manual Download Page 52

     

User Manual                                                                              51 / 54                                                                      CPS Mini Central series 

10 Decommissioning 

10.1 Dismantling the Inverter 

1.

 

Disconnect the inverter as described in section 7. 

2.

 

Remove all connection cables from the inverter. 

 

Danger of burn injuries due to hot enclosure parts! 

Wait 20 minutes before disassembling until the housing has cooled down. 

3.

 

Screw off all projecting cable glands. 

4.

 

Lift the inverter off the bracket and unscrew the bracket screws. 

 

10.2 Packing the Inverter 

If possible, always pack the inverter in its original carton and secure it with tension belts. If it is no longer available, 
you can also use an equivalent carton. The box must be capable of being closed completely and made to support 
both the weight and the size of the inverter. 
 

 

10.3 Disposing of the Inverter 

Do  not  dispose  of  faulty  inverters  or  accessories  together  with  household  waste.  Please 
accordance with the disposal regulations for electronic waste which apply at the installation site at 
that  time.  Ensure  that  the  old  unit  and,  where  applicable,  any  accessories  are  disposed  of  in  a 
proper manner. 

 

 

 

 

Summary of Contents for Mini Central CPSPV30000ETL Series
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands