Custom Equipment Hy-Brid 3 Series Maintenance & Troubleshooting Manual Download Page 5

Lester Prime Charge Status Lights:

SECTION 2 | MAINTENANCE

SECTION 2 | MAINTENANCE

2.1 | BATTERY MAINTENANCE

This unit is equipped with 12-volt AGM maintenance-free batteries. 

NOTE:  The surrounding temperature greatly affects the power reserve within a battery.

EXAMPLE:  A battery that is 100% charged at 80° F (27°C) drops to 65% at 32°F (0°C). At 0°F (-18°C), this battery will 
drop to 40% efficiency.

NEVER ADD ACID TO BATTERY!

2.2 | CHARGING THE BATTERY

 BATTERIES GENERATE EXPLOSIVE GASES. KEEP SPARKS AND FLAME 

AWAY FROM BATTERIES. DO NOT SMOKE WHILE CHARGING.

The charger may include an interlock circuit.  If so equipped, the unit will not operate while charging.   
Operating while charging will shorten battery life.  
 

To charge:

• 

Park the machine on a level surface.

• 

Plug charger into AC outlet until charged.

• 

For best battery life, leave the charger plugged in until machine will be used again.  The charger will maintain the 
battery charge.

DO NOT OPERATE UNIT WHILE 

CHARGING. DO NOT DISABLE 

CHARGER INTERLOCK.

FIGURE 3: Battery Charger LED Display

CAUTION

WARNING

WARNING

Bulk/Start charge cycle phase (constant power or constant current)

Absorption/Plateau charge cycle phase (constant voltage). 
Greater than 80% charged

Finish charge cycle phase (constant current).  Not all charge profiles 
include a Finish phase.  Applies to wet cell batteries only.

Balance/Equalize phase.  An extended charge cycle is occurring 
because a trigger condition has been met (cycle count, etc).  Not all 
charge profiles include a Balance/Equalize phase.  Applies to wet cell 
batteries.  This happens usually every 30 cycles or when the voltage at 
shut off is less than 2.5 volts/cell.  Or 30vdc 

Charge cycle complete

Charge cycle complete.  Post Charge phase (constant voltage flat, etc.)  
Not all charge profiles include a Post Charge phase.  Applies to AGM or 
gel cell batteries only.

AMBER 

(Charge Status)

DESCRIPTION

GREEN 

(Charge Complete)

(SLOW)

(FAST)

(SOLID ON)

(OFF)

(OFF)

(OFF)

(OFF)

(OFF)

(OFF)

(FAST)

(SOLID ON)

(SLOW)

BY  CUSTOM  EQUIPMENT  LLC

BY  CUSTOM  EQUIPMENT  LLC

8

9

MAINTENANCE & TROUBLESHOOTING
HB-1230

SUPO-729

REV B

MAINTENANCE & TROUBLESHOOTING
HB-1230

SUPO-729

REV B

Summary of Contents for Hy-Brid 3 Series
























Reviews: