manualshive.com logo in svg

Custom Engineering TG35/58-T, User Manual

Share
Download
Custom Engineering TG35/58-T User Manual Download Page 13

1. INSTALLATION AND OPERATION

TG35/58-T

3

1-

1.2.1 Configuration of REPORT and FEED keys

If, when the printer is switched on, both of the above-mentioned keys are
held down, the printer enters configuration mode and prints the first
modifiable parameter.
At this point, each time the REPORT key is pressed, the parameter changes
and its current value is printed.
Once the desired value has been obtained, press the FEED key to proceed
to the next parameter, and so on.
Once all the parameters have been run through, the printing of a message
signals the end of setting procedure.

1.3 AUTOTEST

To run the autotest, press the 

FEED 

key while switching on the printer.

During the running of the autotest, the character fonts and logos stored
inside the printer are printed.

1.4 CAUTIONS

WARNINGS:

• Do not print without paper.
• Do not drag the carriage manually when the printer is on.
• Do not allow any foreign bodies to become trapped inside the
printer.
• Safeguard all parts of the printer from blows, both during and
subsequent to installation.

Summary of Contents for TG35/58-T























































Reviews:

No comments

Brands by name

Popular brands

Load more brands