Custom Audio Electronics TG02H Command Manual Download Page 60

Page: 60 / 100

0x1D 0x2A

<GS *>

Define downloaded bit image

Valid for

TG02H

[Format]

ASCII

d1...d(x × y × 8)

Hex

d1...d(x × y × 8)

Decimal

d1...d(x × y × 8)

[Range]

1 ≤ x ≤ 255

1 ≤ y ≤ 48

x × y ≤ 1536

0 ≤ d ≤ 255

[Description]

Defines a downloaded bit image using the number of dots specified by x and y.

x specifies the number of dots in the horizontal direction.

y specifies the number of dots in the vertical direction.

[Notes]

• The number of dots in the horizontal direction is x × 8, in the vertical direction it is y × 8.

• If x × y is out of the specified range, this command is disabled.

• The d indicates bit-image data. Data (d) specifies a bit printed to 1 and not printed to 0.

• The downloaded bit image definition is cleared when:

1) 0x1B 0x40 is executed.

2) 0x1B 0x26 is executed.

Printer is reset or the power is turned off.

• The following figure shows the relationship between the downloaded bit image and the printed data.

MSB

LSB

dy × 2+1

dy+1

dx × y × 8

dy × 2

y × 8 dots

x × 8 dots

[Reference]

[Example]

60 │

ESC/POS™ emulation

Summary of Contents for TG02H





































































































Search results

Summary of Contents for TG02H

Reviews:

Related manuals for TG02H

Brands by name

Popular brands

Custom Audio Electronics TG02H, Command Manual

Search results

Summary of Contents for TG02H

Reviews:

Related manuals for TG02H

Brands by name

Popular brands