manualshive.com logo in svg

Curtiss-Wright SAM/DEC/008, Manual, Page: 9 / 12

Share
Download
Curtiss-Wright SAM/DEC/008 Manual Download Page 9

SAM/DEC/008

9

19 Apr. 2016 | DST/Z/010

CURTISSWRIGHTDS.COM 

9.

In the 

LAN9500A USB 2.0

 properties dialog, select 

USB Bandwidth Usage Mode

 and then select 

Maximum Throughput

 

from the drop-down menu.

10.

On the 

Power Management

 tab, ensure 

Allow the computer to turn off this device to save power

 is not enabled.

Windows Firewall

Because Ethernet packets are sent and received across networks, you may need to configure your Windows Firewall settings to
allow the SAM/DEC/008 to send and receive data.

Status LEDs

The SAM/DEC/008 has two status LEDs: a USB link LED and a PCM decom LED. Refer to the following table for LED

 

descriptions.

LED

RED

BLUE

YELLOW

GREEN

PURPLE

USB link

Reset

System programming

Reserved

ARP - IP 
address 
configured and 
ready for use

SAM/DEC/008 
configuration being loaded

PCM (decom)

No PCM 

lock

1

1.  The SAM/DEC/008 is a minor frame decoder, therefore PCM decom lock means minor frame lock. During normal operation of the 

SAM/DEC/008, this LED and the USB link LED should be green.

N/A

Internal frame 
engine reset

PCM Decom 
lock (sync word 
found)

DCLK seen/recovered but 
no SYNC detected

Summary of Contents for SAM/DEC/008













Reviews:

No comments