ADJUSTING THE GRINDS
ADJUSTING THE GRINDS
ADJUSTING THE GRINDS
ADJUSTING THE GRINDS
ADJUSTING THE GRINDS
Refer to illustration page 2.
1. Empty hopper of coffee beans. Run grinder to clear grinding burrs of coffee.
2. Open housing cover to locate adjustment screw (8) and lock nut (7). Loosen lock nut.
3. Run motor during adjustment. Turning adjustment screw clockwise will result in a finer grind (if, while turning, you hear the
grinding burrs starting to touch, immediately, back off 1/8th turn). Turning counter clockwise will produce a coarser grind.
4. With a screwdriver holding the adjustment screw in place, tighten the locknut.
5. Run some coffee beans through the machine to check the grind adjustment.
6. Replace front cover on machine.
*This adjustment may change the amount of ground coffee dispensed.
F
IND
OUT
MORE
ON
THE
WEB
.
WILBURCURTIS.COM
1
F
IND
OUT
MORE
ON
THE
WEB
.
WILBURCURTIS.COM
Important Safeguards/Conventions
Important Safeguards/Conventions
Important Safeguards/Conventions
Important Safeguards/Conventions
Important Safeguards/Conventions
CAUTION:
CAUTION:
CAUTION:
CAUTION:
CAUTION: Please
use this setup
procedure before
attempting to use this grinder.
Failure to follow the instructions
can result in injury or the voiding
of the warranty.
WARNING
TO AVOID
SCALDING, Do not
remove brewcone
while brew light is flashing.
ISO 9001 REGISTERED
C
Installa
Installa
Installa
Installa
Installation Instructions,
tion Instructions,
tion Instructions,
tion Instructions,
tion Instructions, Ser
Ser
Ser
Ser
Service &
vice &
vice &
vice &
vice & W
W
W
W
Warranty Informa
arranty Informa
arranty Informa
arranty Informa
arranty Information
tion
tion
tion
tion
FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO
WWW.WILBURCURTIS.COM
This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be performed by an
authorized Wilbur Curtis service center.
•
Do NOT immerse the unit in water or any other liquid
•
To reduce the risk of fire or electric shock, do NOT open top panel. No user serviceable parts inside. Repair should be done
only by authorized service personnel.
•
Keep hands and other items away from hot parts of unit during operation.
•
Never clean with scouring powders or harsh implements.
Conventions
Conventions
Conventions
Conventions
Conventions
W
W
W
W
WARNINGS –
ARNINGS –
ARNINGS –
ARNINGS –
ARNINGS – TTTTTo help a
o help a
o help a
o help a
o help avoid personal injur
void personal injur
void personal injur
void personal injur
void personal injuryyyyy
Important Notes/Cautions – from the factor
Important Notes/Cautions – from the factor
Important Notes/Cautions – from the factor
Important Notes/Cautions – from the factor
Important Notes/Cautions – from the factoryyyyy
QUICK ST
QUICK ST
QUICK ST
QUICK ST
QUICK STAR
AR
AR
AR
ART & SETUP - SLG
T & SETUP - SLG
T & SETUP - SLG
T & SETUP - SLG
T & SETUP - SLG
1. Install the grinder on a firm, level base in a location where it can be connected to a grounded electrical outlet of 120VAC,
rated at 15 amps.
2. Test the unit by running some whole bean coffee through the grinder. If any problems are encountered, refer to the
troubleshooting section complete at www.wilburcurtis.com or call Technical Service at 800-995-0417.
SETUP INSTRUCTIONS - ISLG
SETUP INSTRUCTIONS - ISLG
SETUP INSTRUCTIONS - ISLG
SETUP INSTRUCTIONS - ISLG
SETUP INSTRUCTIONS - ISLG
1. Turn both units OFF.
2. Place the grinder close enough to the brewer so the InterLock cable will reach the brewer.
OPERA
OPERA
OPERA
OPERA
OPERATING INSTR
TING INSTR
TING INSTR
TING INSTR
TING INSTRUCTIONS - SLG
UCTIONS - SLG
UCTIONS - SLG
UCTIONS - SLG
UCTIONS - SLG
The SLG grinder is adjusted at the factory to grind 2 - 2.5 ounces of medium roast coffee.
1. Lift off the clear hopper lid and fill the hopper with whole coffee beans.
2. Place a new filter into your brew cone. Slide the brew cone into the brew cone rails on the grinder.
3. Push the START switch on the front panel. The SLG will start to grind coffee into the brew cone.
4. Wait for the grinder motor to stop before removing the brew cone.
W
W
W
W
W
ILBUR
ILBUR
ILBUR
ILBUR
ILBUR
C
C
C
C
C
URTIS
URTIS
URTIS
URTIS
URTIS
C
C
C
C
C
OMP
OMP
OMP
OMP
OMPANY
ANY
ANY
ANY
ANY
, I
, I
, I
, I
, I
NC
NC
NC
NC
NC
.....
Models Included
SLG
ISLG
123456
123456
123456
123456
123456
123456
123456
OPERA
OPERA
OPERA
OPERA
OPERATING INSTR
TING INSTR
TING INSTR
TING INSTR
TING INSTRUCTIONS - ISLG
UCTIONS - ISLG
UCTIONS - ISLG
UCTIONS - ISLG
UCTIONS - ISLG
Factory settings: SMALL grind button, set for 5 seconds (1.3 oz). LARGE grind
button, set at 15 seconds (3.8 oz). ISLG -13, has additional MEDIUM button set
for 10 seconds.
1. Place the brew cone into the rails on the grinder. Press one of the grind
buttons on the switch panel. Ground coffee will start to fill the brew cone.
2. When the grinder motor stops, remove the brew cone and slide it into the rails
on the brewer.
3. Press the brew switch that displays the blinking indicator light. This starts a brew cycle.
To cancel a brew cycle, press the ON/OFF switch on the brewer. Brew cycles in process will be
cancelled.
WILBUR CURTIS COMPANY
Montebello, CA 90640
