HOLE ENLARGEMENT DIAGRAM
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT
1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
1,000
150
22
20
SCION iQ
3/22/2013
11291
40
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
HEX FLANGE NUT
7/16-14
2
1
HEX BOLT
3/8-16 X 1 1/2
4
2
WASHER
3/8"
4
3
CARRIAGE BOLT
7/16-14 x 1 1/2
2
4
.250 x 1.00 x 2.00" SQUARE HOLE SPACER
CM-SP7
2
5
7/16" FISHWIRE
7_16 FISHWIRE
2
6
HEX FLANGE NUT
HFN3816
4
7
ENLARGED ACCESS HOLE
ENLARGED
ACCESS HOLE
EXISTING HOLES
(BOTH SIDES)
EXISTING HOLE
ENLARGED ACCESS HOLE
NOTE:
ENLARGE EXISTING HOLE
TOWARDS OUTSIDE OF FRAME RAIL
TOW LOOP
(BOTH SIDES)
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
- HOLE ENLARGEMENT
- FISHWIRE HARDWARE
1. Enlarge existing hole to allow 7/16" carriage bolts and SP7 spacers to pass through, both sides.
See Hole Enlargement Diagram.
2. Reverse fishwire 7/16" carriage bolts and SP7 spacers through enlarged access holes, both sides.
See Reverse Pull Fishwire Technique
3. Raise hitch into position and loosely secure to carriage bolts using 7/16" hex flange nuts.
Note:
The side plates will slide between the inside of the tow loops.
4. Align holes in side plates with holes in tow loops and secure using 3/8" hex bolts, 3/8" washers
and 3/8" hex flange nuts, as shown.
5. Torque all 7/16" hardware to 70 ft-lbs.
Torque all 3/8" hardware to 45 ft-lbs.
2
1
7
4
5
TOOLS REQUIRED
RATCHET
TORQUE WRENCH
6" EXTENSION
DIE GRINDER
9/16" SOCKET
11/16" SOCKET
SAFETY GLASSES
EURO MOUNT OPTION AVAILABLE
#45571 (1-7/8") AND #45572 (2" BALL)
DESIGNED FOR USE WITH
BALLMOUNT # D-55001 / 45501
3
6
