Curt Group 3015121 Installation Manual Download Page 1

NEED ASSISTANCE?

  

  

844.278.4357

  

  

RA

  

  

PAGE 1

POWERED RUNNING BOARDS 

INSTALLATION MANUAL

Parts List

1

Driver / left running board*

1

Passenger / right running board*

6

Mounting bracket, universal

6

T-rails

30 Flat washer, M8
18 Nylock nut, M8
18 Flat washer, nylon, 3/8"
12 Nylock nut, 5/16"
2

Rubber grommet

4

Door sensor

2

Door sensor extension

4

Magnet

2

Alcohol wipe

1

Power switch

1

Circuit board

1

Anti-seize

1

Wire loom

1

Wiring harness, two-piece

2

LED light

2

LED light bracket

4

Double-sided foam tape, 3/4" x 3/4"

8

Double-sided foam tape, 1/2" x 1/2"

* Running boards sold separately

Torque Specifications

M

et

ric

M6 bolt

3 ft-lbs.

M8 bolt

7 ft-lbs.

M10 bolt

16 ft-lbs.

SA

E

1/4" bolt

3 ft-lbs.

5/16" bolt

7 ft-lbs.

3/8" bolt

16 ft-lbs.

1/2" bolt

28 ft-lbs.

Use above torque setting unless otherwise noted

Tools Required

Ratchet

Drill

Socket set

Drill bit set

Zip ties

Level

Level of Difficulty

Moderate

Notes and Maintenance

Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
No maintenance required on waterproof harness or water-resistant motors.

If mud or dirt is built up on the steps, simply spray them off and let them air dry.
Mild automotive detergent may be used to clean the product. Do not use dish detergent, abrasive 

cleaners, abrasive pads, wire brushes or other similar products that may damage the finish.
Periodic inspection of all wires and connections should be 

performed to ensure there is no visible damage or loose connections.
Refer to the last page of this manual for troubleshooting, 

warranty and product registration information.
Refer to the table to the left when securing hardware during the 

installation process to help prevent damage to the product or vehicle.

Part Numbers

3025121 (brackets)

3025183 (boards)

3048321 (brackets & boards)

3015121 (brackets)

3015183 (boards)

3038321 (brackets & boards)

Product Photo

Powered Running Boards

 

(not included)

Front

Rear

Middle

 WARNING

Improper electrical installation may result in personal injury. Unless 

you are familiar with the installation and handling of electrical systems, 

have this step performed by someone who has that familiarity.

Summary of Contents for 3015121











Reviews: