Currier Tech 300 Series Owner'S Manual Download Page 34 | Manualshive

Page: 34 / 40

background image

34

Customer Service 1-800-377-4532

Currie Technologies

®

Section 5 - FAQ’S

HOW FAR WITH THE ELECTRO-DRIVE™ SCOOTER GO ON A FULL

CHARGE?

Maximum range per charge for the 300 and 4.0 series scooters is 7
miles (11 km), 400 and 500CD series scooters is 8 miles (13 km) and the
650CD, 750CD and 900CD series scooters is 12 miles (19 km).

Note:

Range per charge of the scooter depend on many variables, includ-

ing but not limited to: riding conditions, rider weight, battery charge, etc.
Riding at full speed will dramatically reduce your range.

WHAT IS THE TOP SPEED OF THE SCOOTER?

Your Electro-Drive™ scooter will accelerate up to 12 mph (20 km/h) for
the 300 and 4.0 series scooters and up to 15 mph (24 km/h) for the 400,
500CD, 650CD, 750CD and 900CD series scooters.

Note:

Top speed of the scooter depend on many variables, including but

not limited to: riding conditions, rider weight, battery charge, etc.

WHAT IS THE WEIGHT LIMIT OF MY SCOOTER?

Maximum rider weight is 180 lbs, (82 kg) for the 300 and 4.0 series scoot-
ers, 240 lbs. (109 kg) for the 400 and 500CD series scooters and 260 lbs.
(118 kg) for the 650CD, 750CD and 900CD series scooters; never exceed
it.

CAN I RIDE MY SCOOTER IN WET CONDITIONS OR ON WET PAVE-

MENT?

No! Riding in wet conditions can cause the rider to lose control and due
to the possibility that water might enter the electrical components (battery
compartment, motor, controller, etc.) causing them to fail, we strongly
recommend you do not operate the scooter in wet conditions, through
puddles, in snow or anywhere your scooter is likely to get wet. Currie
Technologies

®

does not recommend riding on wet conditions.

WHAT IS THE CORRECT AIR PRESSURE FOR THE TIRES?

For scooters equipped with a solid tire(s) in

fl

ating the tires is not necessary.

For scooters equipped with pneumatic tires check tire pressure imprinted
on the sidewall of the tire. In

fl

ate to recommended pressure as necessary.

Never in

fl

ate a tire beyond the maximum pressure im-

printed on the sidewall

•

•

•

•

•

WARNING

!

Chain Drive Scooters.indd 34

Chain Drive Scooters.indd 34

3/18/2008 12:18:53 PM

3/18/2008 12:18:53 PM

«
...
32
33
34
35
36
...
»

Summary of Contents for 300 Series









































Reviews:

No comments

Related manuals for 300 Series

Brand: Xootr Pages: 2

Brand: Jeep Pages: 316

Brand: Rascal Pages: 32

Brand: Rascal Pages: 32

Brand: SWAGTRON Pages: 27

Brand: UFREE SCOOTER Pages: 12

EXIT-CROSS ENTRY

Brand: IO Hawk Pages: 42

Brand: KYMCO Pages: 41

Brand: Huffy Pages: 6

SPEEDFIGHT 3 RS

Brand: PEUGEOT Pages: 1

Brand: PEUGEOT Pages: 15

Brand: PEUGEOT Pages: 28

Brand: PEUGEOT Pages: 64

Brand: Jotagas Pages: 33

Brand: Kinroad Pages: 34

Brand: Shoprider Pages: 24

Brand: Lehe Pages: 13

Brand: Scooter Pages: 208

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands