Current Cost EnviR User Manual Download Page 8 | Manualshive

Page: 8 / 12

Current Cost EnviR User Manual Download Page 8

8

EnviR - The SmartR Monitor

• Check the display to ensure that it is reading the signal and that watts are being displayed.
• Re-attach the protective cover and close the panel.
• Turn On the Main Breaker.

setting the clock

• Press the OK button for three seconds.
• The screen will clear and clock hours will flash.
• Use the UP ( ) or DOWN (V) buttons to adjust the hour.
• Once the correct hour is selected press OK button.
• The minutes will now flash. Use the UP ( ) or DOWN (V) buttons to adjust

the minutes. Once the correct minute has been selected press the OK button.

setting the base Rate

The unit has been programmed with a default rate of $0.1396 cents per kWh. To find out your
local rate, contact your local utility or review your last utility bill and divide the total bill amount /
KWhs used. To adjust your rate:

• Push the UP ( ) button and hold for three seconds.
• Press OK. The display will flash normal price.
• Press UP ( ) or DOWN (V) buttons to adjust price on first 2 digits.
• Press OK. The display will flash last 2 digits.
• Press UP ( ) or DOWN (V) buttons to adjust price on last 2 digits.
• Press OK.

multiple Rate Tariffs

The EnviR can be programmed to calculate different KWh unit rates for electricity consumed at different
times of day. In order to program different rates:
• Press and hold the UP ( ) and DOWN (V) buttons together until the LED flashes. Then release both

buttons.

• Using the UP ( ) and DOWN (V) buttons you can select your low cost rate. Press the OK button to

confirm rate.—If you do not select a different rate, then you will not see the time section.

• You will see the clock flashing. Using the UP ( ) and DOWN (V) buttons you can now set the time that

your low rate starts. Press the OK button to confirm.

• Using the UP ( ) and DOWN (V) buttons you can set the time your normal rate starts.

Press the OK button to confirm.

• The display will resume normal operation.

Time

Last Days

Yesterday

kWh

Night

Per
Day

Day Eve

Appliance

Time

30

kW

Energy Now
Cost

$

PowerSave Envi R Man.indd 8

04/08/2011 10:27

«
...
6
7
8
9
10
...
»

Summary of Contents for EnviR













Reviews:

No comments