Packaging and Enclosed Parts
Please inspect your pack for damaged or missing parts. Notify your supplier if any discrepancies occur.
The SUB801-70V Speakers are packaged one to a box and sold as each.
Each box includes (1) Speaker, (1) Grille(1) ½” knockout cover plate and (1) Hardwood Tree planted in the National Forest.
Specifications subject to change without notice.
Install
1.
Decide if you want standard 8 ohm or distributed 70/100volt speaker sound. Then chose 8 ohm or 70Volt. The PRO SUB801-70V can do either. This speaker may
also be used on 100 volt systems but with derated taps. See chart below
2.
Chose locations for your speakers. I suggest one Pro SUB801 every 275 sqft
3.
Choose your wiring method: Home Run or Daisy chain. Suggest a pigtail if daisy chain from one speaker to the next. Use Home Run wiring in 8 ohm applications.
4.
Bury your conduit or wire 18” below grade to prevent damage by tillers or shovels when planting. Prewire before hardscape concrete.
5.
Insure there is enough room above to place the SUB801-70V in the ceiling or tile.
6.
Use a one piece TB8 Tile Support Bracket to prevent sag.
See YouTube for video install instructions
. Cut on inside of TB8 diameter
7.
For proper phasing identify the (+) and (-) on each cable.
8.
If using as 70 volt the speakers they can be Daisy Chained from one speaker to the next.
9.
How do I know what size 70 volt amp to use? Rule of thumb - add up all the wattage taps of the speakers then divide by .75 for safety factor. Example, suppose you
have 5 speakers with the wattage tap of 30, the total wattage would be 150 watts. Divide 150W/.75 = 200W. Now select an amp of 200W or higher.
10.
For 8ohm hook-up select the 8
Ω position on the Tap switch on the rear of the back-can.
11.
Before connecting the wires to the amplifier check the impedance with a multi-meter on the resistance scale. It should read about 6.5 ohms in the 8 ohm position.
12.
If multi-meter reading is OK, observe polarities then connect to amplifier.
Limited Lifetime Warranty
Current Audio speakers are warranted to be free from defects in materials and or workmanship to the original retail purchaser provided the speaker was
purchased and installed from a Current Audio Authorized Dealer.
In the event of defective materials and or workmanship, Current Audio, LLC will, without change, repair or replace, at its option, the defective product. In
order to make claim under this Warranty and to obtain performance of any obligation under warranty, please contact Current Audio LLC. Instructions will be
given on how to return the defective product to Current Audio. Returned products must be shipped prepaid. Proof of purchase must be provided with the
product.
The Warranty does not apply to damage not resulting from defective materials and or workmanship while in the possession of the original consumer or due to
unreasonable use by the original consumer, which includes but not limited to improper installation, negligence, unauthorized repair or modification, aesthetic
deterioration from the environment. Products purchased by unauthorized sources will void the warranty and not be honored.
Current Audio ,LLC is not liable for any incidental or consequential damages, so the above limitations or inclusion may not apply to you. This warranty gives
you specific legal rights, and you may have other rights, which vary from state to state within the United States.
SUB801-70V RPA 062811
¼-20
PRO SUB801-70V
In-Ceiling Sub Woofer
User’s Installation Guide
TB8 Tile Support Bracket
TB8 Tile Support Bracket used as a template
Tile-Bracket-Speaker
70 Volt Input
100 Volt Input
30 Watt
DO NOT USE
15 Watt
30 Watt
7.5 Watt
15 Watt
100 Volt Conversion Chart
