Cumberland PNEG-240 Installation And Operation Manual Download

Page: 61 / 76

10. Parts List

PNEG-240

Chain Feeding System

2 Line, 1 Way Belt Drive Mini Hopper (C4920001-60 and C4920001-120) Parts List

Ref #

Part #

Description

Qty

C4920001-60

2 Line, 1 Way 60 FPM Belt Drive

C4920001-120

2 Line, 1 Way 120 FPM Belt Drive

7097719

2 Line, 1 Way Drive Hopper (Painted)

HH-3008

Insert, Threaded 1/4"-20 Steel/Cadmium

07097598A

Chain Guide with Hardware

S-1101

Bolt, HHCS 1/4"-20 x 1/2" ZN Grade 2

7099362

2 Line, 1 Way Feed Return Wheel Slide

S-2041

Split Lock Washer 1/4" ZN

7097652

Bearing 1" Flange 4 Hole

7097682

Drive Shaft

7097737

Gearbox, Leedy, 52:1, Belt Drive, Right Hand (60 FPM)

7098744

Gearbox, Leedy, 37:1, Belt Drive, Right Hand (120 FPM)

7097930

Chain Coupler 1" Sprocket

7097932

Chain #40 Chain W/ Coupler Feed

7097696-B

Yoke Assembly

7097506

Drive Sprocket 3/8"

07097579A

Sheave, 2 Grade 2.95 O.D. 3/4" Bore SS

7098283

3/16" x 1-1/4" Key

7099513

3/16" x 1-1/4" Shear Pin (Hard Grade)

7099143

Drive Sprocket Collar

S-4454

Pin, Spring 1/4" x 2" Roll

S-3883

Bolt, HHTB 1/2"-13 x 1-3/4" YDP Grade 8

S-236

Split Lock Washer 1/2" REG ZN Plated

S-3729

Hex Nut 1/2"-13 YDP Grade 5

S-7486

Flange Bolt 3/8"-16 x 1-1/2" JS500 Grade 8 or 8.2 Full Thread

S-248

Flat Washer 3/8" 7/16" I.D. 1" O.D. YDP

S-4663

Stover Nut 3/8"-16 ZN Grade 2

S-9169

Key, Square 1/4" x 1-1/2"

S-7371

Screw, Set 5/16"-18 x 1/2"

7097731

Power Shoe Wear Plate Assembly

S-7185

Bolt, HHCS 3/8"-16 x 5/8" ZN Grade 2

7097681

Intake Wheel Feeder Shaft

S-7241

Cotter Pin 1/8" x 1-1/4" ZN Grade 2

7097609

Intake Wheel Weldment

7100637

Bearing Bronze

7097675

Feed Level Plate 2 Line Mini

S-6076

Carriage Bolt 5/16"-18 x 3/4" ZN Grade 2

S-845

Flat Washer 5/16" USS SAE YDP Grade 2

S-4301

Wing Nut 5/16"-18 ZN Grade 2

C4000169-RD

Chain Stripper Assembly, 2L, 4L, 6L

S-4275

Bolt, HHTB 5/16"-18 x 3/4" ZN Grade 5

S-5220

Nylock Nut 5/16" ZN Grade 5

7097676

Drive Guard Assembly

7097544

Motor Mount Support Angle

7098748

Motor Mount

S-7086

Bolt, HHTB 5/16"-18 x 3" ZN Grade 2

S-10268

Flange Nut 5/16"-18 JS500 Grade 5

7098223

Cap, Round, Fits 0.500-0.563 O.D., 0.500 HT.

DC-897

Decal, Cumberland Chain Feeder

DC-996

Decal, Warning Chain Sprocket

Summary of Contents for PNEG-240













































































Search results

Summary of Contents for PNEG-240

Reviews:

Related manuals for PNEG-240

Brands by name

Popular brands

Cumberland PNEG-240, Installation And Operation Manual

Search results

Summary of Contents for PNEG-240

Reviews:

Related manuals for PNEG-240

Brands by name

Popular brands