Cumberland PNEG-240 Installation And Operation Manual Download

Page: 5 / 76

1. Safety

PNEG-240

Chain Feeding System

Cautionary Symbols Definitions

Cautionary symbols appear in this manual and on product decals. The symbols alert the user of potential
safety hazards, prohibited activities and mandatory actions. To help you recognize this information, we
use the symbols that are defined below.

DANGER

WARNING

CAUTION

NOTICE

This symbol indicates an imminently hazardous situation
which, if not avoided,

will result in serious injury or death.

This symbol indicates a potentially hazardous situation
which, if not avoided,

can result in serious injury or death.

This symbol indicates a potentially hazardous situation which,
if not avoided,

can result in minor or moderate injury.

This symbol is used to address practices not related to
personal injury.

This symbol indicates a general hazard.

This symbol indicates a prohibited activity.

This symbol indicates a mandatory action.

ST-0005-2

Summary of Contents for PNEG-240













































































Search results

Summary of Contents for PNEG-240

Reviews:

Related manuals for PNEG-240

Brands by name

Popular brands

Cumberland PNEG-240, Installation And Operation Manual

Search results

Summary of Contents for PNEG-240

Reviews:

Related manuals for PNEG-240

Brands by name

Popular brands