manualshive.com logo in svg

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 55 / 142

Share
Download
Culligan G1 Series Installation, Operation And Service Instructions Download Page 55

Accessories    

51

Cat. No. 01021713

Alarm Outputs

Alarm Relay Board

The GBE RO controller board offers support for the Culligan Alarm Relay board (P/N 01022238). See Figure 28. To use 

the alarm relay board, install it onto the back of the GBE RO controller board. See Figure 29.

Figure 28. 

Alarm Relay board. 

PLUG IN

HERE

ALARM

BOARD

RELAY

BACK OF

GBE BOARD

Figure 29. 

Alarm Relay board install to GROC.

The alarm relay board is plugged into the GBE RO controller board alarm relay socket. When Error Status is selected on 

the GBE RO controller, this relay will be in the Normally Open position when the controller board has power on AND there 

are no errors present (i.e. “Problem Found” is not showing on the Home screen.)  The relay will be in the Normally Closed 

Position when the controller is either powered OFF or there is an error present on the controller board.  

NORMAL OPERATION:

Terminals NO and NC are connected, 

leaving the lamp circuit open (lamp off)

ERROR CONDITION:

Terminals NO and COM are connected, 

completing the lamp circuit (lamp on)

ALARM SIGNAL PCB

LAMP or BUZZER

24VAC SUPPLY

RELAY

Figure 30. 

Example of customer wiring to the GROC Alarm Signal Output 

RUNNING

JAN-01-12 12:01P

1.  From the default home screen, press  

. The screen displays the main menu.

Summary of Contents for G1 Series















































































































































Reviews:

No comments