manualshive.com logo in svg

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 33 / 142

Share
Download
Culligan G1 Series Installation, Operation And Service Instructions Download Page 33

First Time Setup    

29

Cat. No. 01021713

Wiring for Softeners and Filters with GBE RO Controller

For these systems, you must add a 24 VAC relay, part number 01016156, to provide the pretreatment contact.
GBE to Relay: Connect a wire from terminal 5 of the relay to the left terminal of Aux 4 on the GBE softener/filter circuit 

board. Connect another wire from terminal 1 of the relay to the right terminal of Aux 4. Refer to 

Figure 19

.

Relay to GBE RO controller: Connect a wire from the POSITION (J2), PIN 3 terminal on the AUX board  to terminal 3 on 

the relay. Connect another wire from the POSITION (J2), PIN 4 terminal on the AUX board to terminal 4 on the relay. Use 

the GBE RO controller Aux cable kit, P/N 01021830, to connect cables to the GBE RO controller board.

Relay

J7

J10

J5

J6

J16

J17

J2

GROC BOARD

GBE SOFTENER/FILTER

AUX OUT 4

Figure 19. 

 GBE to GBE RO controller relays.

Summary of Contents for G1 Series















































































































































Reviews:

No comments