Culligan G1 Series Installation, Operation And Service Instructions Download Page 26

Page: 26 / 142

Culligan® Series G1 Reverse Osmosis

Cat. No. 01021713

Menu Lockout

It is possible to lock the keypad of the Global RO controller so that users will only have access to the INFORMATION, GO

TO RUNNING, and GO TO OFFLINE menu screens.

To lock the system, press and hold

and

for 10 seconds. Repeat this process to unlock the keypad.

NOTE Menu lockout may be completed only from the home screen.

Menu Default—Rerun First Time Setup

Below is the procedure to default the board to factory settings and begin the first time setup.

1. Power down the control.

2. Press and hold

and

3. Power up the control while continuing to hold

and

for at least five (5) seconds.

4. Release

and

. The display should be blank—if not go back to step 1.

5.  Power down the control.
6.   Power up the control again. The screen lights up for two seconds and then displays the home screen.
7.  Follow the first time setup process.

Flow Meters

There are two flow meters on the G1 RO system, the feed flow meter (FM1) and the product flow meter (FM2). Before

using the G1 RO it is necessary to first calibrate both flow meters. See Table 1.
Connect the wires of both flow meters to the CIB board using the 4 - pin connections provided. The feed flow meter con-

nects to FM1 (J11) and the product flow meter connects to FM2 (J12). See Figure 17.
The pins are:
Pin 4 = not connected
Pin 3 = ground
Pin 2 = flow pulse signal
Pin 1 = 5 VDC power supply

NOTE Pin 1 on the GBE board is identified with a small WHITE dot.

J15—INLET FLOW

METER

FLOW METER

J1—PRODUCT

J10

J16

J17

The 4 - Pin Connections are:

4 = n/c, 3 = ground, 2 = flow pulse signal, 1 = 5 VDC supply

NOTE: Pin 1 is identified with a small WHITE dot.

Figure 17.

Flow Meter Connections on GBE Board

Summary of Contents for G1 Series















































































































































Search results

Summary of Contents for G1 Series

Reviews:

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 26 / 142

Search results

Summary of Contents for G1 Series

Reviews: