To Program the Brew Time
To program the brew time, press and hold the program button for two
seconds. The “prog” symbol starts flashing in the lower right corner
of the LCD screen.
Press the hour button to advance the clock to the desired time. The
hour numeral moves in one hour increments. When numeral passes
12 am, the “PM” indicator will illuminate in the lower left hand corner of
the LCD screen.
Press the “minute” button to advance the minutes to the desired time.
Minutes move in one second increments.
When complete, press the “prog” button, or wait for 15 seconds and
your set time will be accepted.
To Activate the Auto Brew Cycle
To activate the auto brew mode, depress the “auto on” button.
The “auto” symbol will illuminate in the upper right hand corner of the
LCD screen.
The unit will now begin the brewing cycle at the programmed time.
When the programmed time initiates the cycle, the red “ON” indicator
light will show that the brewing cycle has started.
NOTE: The unit will continue to attempt to brew at the programmed time, each
day, until the Auto On button is turned off. The red “ON” indicator light will
illuminate each time the attempt to brew is made.
If there is no water in the reservoir, the unit will automatically shut off
one minute later.
COFFEE PREPARATION
1. Place coffeemaker on a solid flat surface.
Plug into 120V outlet.
2. Open thermal carafe lid in direction of “OPEN” arrow. Fill thermal
carafe with cold, fresh water. Open hinged water reservoir cover;
pour water into reservoir opening. Markings on water level indica-
tor show amount of water needed to make desired number of cups
of coffee. TO AVOID OVERFLOW, DO NOT FILL ABOVE 8-CUP
MARK. Close reservoir cover.
3. Before thermal carafe is returned to platform, prewarm carafe by
running warm water through it. If warm water is not run through
carafe, when hot coffee flows into carafe during brewing cycle the
glass liner may crack due to the temperature change.
Prewarming carafe will help keep coffee warmer, and also
prevent glass liner from being damaged.
4. Return carafe lid to thermal carafe. To close lid, turn it in direction of
“CLOSE” arrow until it fits tightly on carafe, and “POUR” arrow is
aligned with spout. Return empty thermal carafe to platform.
Be certain thermal carafe lid is in “CLOSED” position and is
securely in place during brew cycle.
5. Open filter basket by grasping basket handle and swinging
outward. Insert a filter into filter basket; make sure filter fits snugly
in basket. Use a fresh filter for each carafe of coffee.
6. After placing 2 level tablespoons per cup of ground coffee into cone
filter, return basket to closed position. To ensure safe operation,
make sure basket is closed securely.
7. With thermal carafe and basket securely in place, press “ON”
button; LED will light.
CAUTION:
Coffeemaker becomes very hot
during brew cycle; handle with extreme care, as hot parts and
escaping steam may cause burns.
8. The Brew-Through lid allows coffee to drip from coffeemaker
through closed lid. When coffee has completely stopped dripping
into thermal carafe and water level indicator is empty, brew cycle is
complete. When dripping stops, Brew-Through lid will seal so coffee
freshness and temperature are preserved.
9. An audible “beep” tone will signal when brew cycle is complete.
Coffeemaker will switch off automatically.
10. After coffee grounds have cooled, carefully open filter basket and
discard used coffee filter and grounds. To remove filter basket from
coffeemaker (A) grasp basket handle and swing basket outward,
and (B) with basket in far right position, lift up and pull
basket hinge.
11. Brew-Through lid allows coffee to be poured with lid in “CLOSED”
position, so coffee freshness and temperature can be preserved.
NEVER POUR LIQUID FROM THERMAL CARAFE UNLESS LID IS
IN “CLOSED” POSITION.
PAUSE & SERVE
This feature allows a cup of coffee to be poured before brew cycle has
finished. Carefully remove thermal carafe, and the Pause & Serve fea-
ture will be automatically activated, temporarily stopping flow of coffee
into thermal carafe. Return thermal carafe to platform immediately after
pouring coffee, and the brewing process will resume.
3
