background image

59

CUB CADET CORPORATION

MANUFACTURER’S LIMITED WARRANTY

(RESIDENTIAL USE)

The limited warranty set forth below is given by CUB CADET
CORPORATION (“CUB CADET”) with respect to new
merchandise purchased and used in the United States, its
possessions and territories.

CUB CADET warrants this product against defects in material
and workmanship for a period of two (2) years for residential
users, (one (1) year for commercial users), commencing on the
date of original purchase and will, at its option, repair or
replace, free of charge, any part found to be defective in
material or workmanship.  This limited warranty shall only apply
if this product has been operated and maintained in
accordance with the Operator’s Manual furnished with the
product, and has not been subject to misuse, abuse, neglect,
accident, improper maintenance, alteration, vandalism, theft,
fire, water or damage because of other peril or natural disaster.
Damage resulting from installation or use of any part,
accessory, or attachment not approved by Cub Cadet for use
with the product(s) covered by this manual will void your
warranty as to any resulting damage.

Batteries and belts are subject to separate terms as follows:

a.

Batteries have a one-year prorated limited warranty
with 100% replacement during the first three months.
After three months, the battery replacement credit is
based on the months remaining in the twelve (12)
month period dating back to the original date of sale.
Any replacement battery will be warranted only for the
remainder of the original warranty period.

b.

All belts are covered by a one (1) year limited war-
ranty against defects in material and workmanship.

3 Year Limited Warranty - PTO Clutch

CUB CADET warrants the power take off (PTO) clutch and
mounting hardware against defects in material and workman-
ship for a period of three (3) years for Series 2000 products for
residential users, commencing on the date of original pur-
chase or lease and CUB CADET will, at its option, repair or re-
place, free of charge, any PTO clutch or mounting hardware
found to be defective in material or workmanship provided this
product has been operated and maintained as set forth above.

5 Year/500 Hour Limited Warranty

CUB CADET warrants the frame, front cast iron pivot axle and
drive shaft on Series 2000 and 3000 models against defects
in material and workmanship for a period of five (5) years or
500 hours, whichever occurs first, for residential users,
commencing on the date of original purchase or lease and
CUB CADET will, at its option, repair or replace, free of
charge, any part found to be defective in material or
workmanship provided this product has been operated and
maintained as set forth above.  In addition to any other reason
set forth herein, CUB CADET may deny warranty coverage if
the hour meter, or any part thereof, is altered, modified,
disconnected or otherwise tampered with.

HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE, THROUGH YOUR LOCAL
AUTHORIZED CUB CADET DEALER. To locate the dealer in
your area, please check for a listing in the Yellow Pages or
contact Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio
44136-0019, or call 1-877-282-8684, or log on to our Web site
at www.cubcadet.com.

This limited warranty does not provide coverage in
the following cases:

a.

Routine maintenance items such as lubricants, filters,
blade sharpening, tune-ups, brake adjustments, clutch
adjustments, deck adjustments, and normal deteriora-
tion of the exterior finish due to use or exposure.

b.

CUB CADET does not extend any warranty for
products sold or exported outside of the United
States of America, its possessions and territories,
except those sold through CUB CADET’s authorized
channels of export distribution.

c.

Replacement parts that  are not genuine Cub Cadet
parts.

d.

Service completed by someone other than an
authorized service dealer.

e.

Transportation charges and service calls.

No implied warranty, including any implied warranty of
merchantability or fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified.  No other
express warranty, whether written or oral, except as
mentioned above, given by any person or entity,
including the dealer, with respect to any product, shall
bind CUB CADET.  During the period of the warranty, the
exclusive remedy is repair or replacement of the product
as set forth above.
 

The provisions as set forth in this Warranty provide the
sole and exclusive remedy arising from the sales.  CUB
CADET shall not be liable for incidental or consequential
loss or damages including, without limitation, expenses
incurred for substitute or replacement lawn care
services or for rental expenses to temporarily replace a
warranted product.
 

Some states do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above exclusions or
limitations may not apply to you.

In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold.  Alteration
of the safety features of the product shall void this
Warranty
. You assume the risk and liability for loss,
damage, or injury to you and your property and/or to others
and their property arising out of the use or misuse or inability
to use the product.

This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased
as a gift.

How State Law Relates to this Warranty:

    This

limited warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.

                      IMPORTANT: Owner must present Original Proof of Purchase to obtain warranty coverage.

                               

Cub Cadet LLC, P.O. BOX 361131 CLEVELAND,OHIO 44136-0019; Phone: 1-877-282-8684

Summary of Contents for GT 2186-44





























































Reviews: