Cub Cadet CC924 Operator'S Manual Download

Page: 2 / 20

Safety Instructions..........................................3

Visit us on the web at www.mtdproducts.com

Contact MTD AU • P.O. Box 376 Dandenong.V

ic.31

Email Address: [email protected] Customer Service Ph

one:1300 951 594

Symbols...........................................................5

Get to know yur brush cutter.........................

Assembly Instructions....................................9

Fuel and

il Instructions..............................11

peratin

Instructions.................................12

Maintenace and repair.................................14

Cleanin

and Stora

e..................................1

Tro

Contents ....................................................... 20

ubleshootin

...........................................18

Before setting up and operating your new equipment,

please locate the model plate on the equipment and record

the information in the provided area to the right. You can

locate the model plate on the engine of the brushcutter

This information will be necessary, should you seek technical

support via our web site, Customer Support Department,

or with a local authorized service dealer.

Summary of Contents for CC924





















Search results

Summary of Contents for CC924

Reviews:

Related manuals for CC924

Brands by name

Popular brands

Cub Cadet CC924, Operator'S Manual

Search results

Summary of Contents for CC924

Reviews:

Related manuals for CC924

Brands by name

Popular brands