Cub Cadet CC2090 Operator'S Manual Download Page 2

2

READ ALL INSTRUCTIONS BEFORE OPERATING

• Read the instructions carefully. Be familiar with the controls

and proper use of the unit.

• Do not operate this unit when tired, ill, or under the influence

of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use the unit,

except for teens guided by an adult.

• All guards and safety attachments must be installed properly

before operating the unit.

• Inspect the unit before use. Replace damaged parts. Check

for fuel leaks. Make sure all fasteners are in place and secure.
Replace parts that are cracked, chipped, or damaged in any
way. Do not operate the unit with loose or damaged parts.

• Carefully inspect the area before starting the unit. Remove all

debris and hard or sharp objects such as glass, wire, etc.

• Be aware of the risk of injury to the head, hands and feet.
• Clear the area of children, bystanders, and pets. At a

minimum, keep all children, bystanders, and pets outside a 50
feet (15 m.) radius; there still may be a risk to bystanders from
thrown objects. Bystanders should be encouraged to wear
eye protection. If you are approached, stop the unit
immediately.

• Use only 0.105 inch (2.67 mm) diameter original equipment

manufacturer replacement line. Never use metal-reinforced
line, wire or rope. These can break off and become dangerous
projectiles. 

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments or
repairs before using unit.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Avoid creating a source of ignition for spilled fuel. Do not start

the engine until fuel vapors dissipate.

• Always stop the engine and allow it to cool before filling the

fuel tank. Never remove the cap of the fuel tank, or add fuel,
when the engine is hot. Never operate the unit without the fuel
cap securely in place. Loosen the fuel tank cap slowly to
relieve any pressure in the tank.

• Mix and add fuel in a clean, well-ventilated outdoor area

where there are no sparks or flames. Slowly remove the fuel
cap only after stopping engine. Do not smoke while fueling or
mixing fuel. Wipe up any spilled fuel from the unit
immediately. Always wipe unit dry before using.

• Move the unit at least 30 feet (9.1 m) from the fueling source

and site before starting the engine. Do not smoke or allow
sparks and open flames near the area while adding fuel or
operating the unit.

WHILE OPERATING

• Never start or run the unit inside a closed room or building.

Breathing exhaust fumes can be fatal. Operate this unit only in
a well-ventilated outdoor area.

• Wear safety glasses or goggles that meet ANSI Z87.1

standards and are marked as such. Wear ear/hearing
protection when operating this unit. Wear a face or dust mask
if the operation is dusty.

• Wear heavy long pants, boots, gloves and a long sleeve shirt.

Do not wear loose clothing, jewelry, short pants, sandals or
go barefoot. Secure hair above shoulder level.

• The cutting attachment shield must always be in place while

operating the unit as a trimmer. Do not operate unit without

RULES FOR SAFE OPERATION

• IMPORTANT SAFETY INSTRUCTIONS •

Read the Operator’s Manual and follow all warnings and safety instructions. Failure to do so can result in serious injury to the

operator and/or bystanders.

FOR QUESTIONS, CALL 1-877-282-8684 IN U.S. OR 1-800-668-1238 in CANADA

The purpose of safety symbols is to attract your attention to possible
dangers. The safety symbols, and their explanations, deserve your
careful attention and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or warnings they
give are not substitutes for proper accident prevention measures.

NOTE:

Advises you of information or instructions vital to the
operation or maintenance of the equipment.

SAFETY ALERT:

Indicates danger, warning or

caution. Attention is required in order to avoid
serious personal injury. May be used in conjunction
with other symbols or pictographs.

DANGER:

Failure to obey a safety warning will

result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the
risk of fire, electric shock and personal injury.

WARNING:

Failure to obey a safety warning can

result in injury to yourself and others. Always follow
the safety precautions to reduce the risk of fire,
electric shock and personal injury.

CAUTION:

Failure to obey a safety warning may

result in property damage or personal injury to yourself
or to others. Always follow the safety precautions to
reduce the risk of fire, electric shock and personal injury.

SYMBOL

MEANING

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the states of
California, Maine, Oregon and Washington.

All U.S. Forest

Land and the state of California (Public Resources Codes 4442
and 4443), Oregon and Washington require, by law that certain
internal combustion engines operated on forest brush and/or
grass-covered areas be equipped with a spark arrestor,
maintained in effective working order, or the engine be
constructed, equipped and maintained for the prevention of
fire. Check with your state or local authorities for regulations
pertaining to these requirements. Failure to follow these
requirements could subject you to liability or a fine. 

This unit is

factory equipped with a spark arrestor

. If it requires

replacement, ask your LOCAL SERVICE DEALER to install the

Accessory Part #753-05169 Muffler Assembly

.

CALIFORNIA PROPOSITION 65 WARNING

WARNING

THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO

CAUSE CANCER, BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

WARNING:

When using the unit, you must follow

the safety rules. Please read these instructions before
operating the unit in order to ensure the safety of the
operator and any bystanders. Please keep these
instructions for later use.

WARNING:

Gasoline is highly flammable, and its

vapors can explode if ignited. Take the following
precautions:

Summary of Contents for CC2090





























































Reviews: