Cub Cadet CC 350 Operator'S Manual Download Page 4

• SAFETY & INTERNATIONAL SYMBOLS •

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's
manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL

MEANING

SYMBOL

MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used in
conjunction with other symbols or pictographs.

• READ OPERATOR'S MANUAL

WARNING: 

Read the operator’s manual(s) and

follow all warnings and safety instructions. Failure to
do so can result in serious injury to the operator
and/or bystanders.

• WEAR EYE AND HEARING PROTECTION

WARNING:

Thrown objects and loud noise can

cause severe eye injury and hearing loss. Wear eye
protection meeting current ANSI Z87.1 standards and
ear protection when operating this unit. Use a full face
shield when needed.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• OIL

Refer to operator’s manual for the proper type of oil.

• DO NOT USE E85 FUEL IN THIS UNIT

WARNING:

It has been proven that fuel containing

greater than 10% ethanol will likely damage this
engine and void the warranty.

• ON/OFF STOP CONTROL

ON / START / RUN

• ON/OFF STOP CONTROL

OFF or STOP

• PRIMER BULB

Push primer bulb, fully and slowly, 10 times.

• CHOKE CONTROL

1. • FULL choke position
2. • PARTIAL choke position
3. • RUN choke position

• THROWN OBJECTS AND ROTATING CUTTER CAN

CAUSE SEVERE INJURY

WARNING:

Small objects can be propelled at high

speed, causing injury. Keep away from the rotating rotor.

• KEEP BYSTANDERS AWAY

WARNING:

Keep all bystanders, especially children

and pets, at least 50 feet (15 m) from the operating area.

• HOT SURFACE

WARNING

Do not touch a hot muffler or cylinder.

You may get burned. These parts get extremely hot
from operation. When turned off they remain hot for a
short time.

• SHARP BLADE

WARNING:

Sharp blade on trimmer attachment

shield. To prevent serious injury, do not touch the line
cutting blade.

4

Summary of Contents for CC 350

























































Reviews: