Cub Cadet 53TIHKTY050, Operator'S Manual

Page: 21 / 32

21 S
ection
4 — P
roduct
c
are
• Clean the top of the mower deck, under
the spindle covers and belt area. See
Figure 4-2.
Figure 4-2
• Clean around and near the transmission,
axle and the fan area. See Figure 4-3.
Wheel Not Shown For Clarity
Figure 4-3
• Debris can accumulate anywhere on the
tractor, especially on horizontal surfaces.
Additional cleaning may be necessary
when mowing in dry conditions or
when mulching.
• Fuel leaks/spills, oil leaks/spills and
excess lubrication can also become
collections sites for debris. Immediate
repair and cleaning up oil or fuel spills
can help reduce fire hazards.
• In addition to cleaning the tractor before
operating and storing, do not attempt to
mow unusually tall grass (10” or higher),
dry grass (e.g., pasture) or piles of dry
leaves. Dry grass or leaves may contact
the engine exhaust and/or build up on
the mower deck presenting a potential
fire hazard.
Storing the Tractor
• Allow the machine to cool in an open
area before storing.
• Do not park the tractor near any
flammable materials (wood, cloth or
chemicals) or any open flames or other
potential source of ignition (furnace,
water heater or any other type of heater).
• Remove all combustible materials from
the tractor before storing. Empty cargo
boxes, grass catchers or containers.
• Always shut off fuel flow when storing or
transporting if tractor is equipped with a
fuel shutoff.
• Check the fuel system (lines, tank, cap
and fittings) frequently for cracks or
leaks. Repair and clean as necessary.
Engine
Refer to the Engine Operator’s Manual for all
engine maintenance intervals, procedures,
specifications and instructions.
Changing the Engine Oil
WARNING
If the engine has been recently run, the engine, muffler,
and surrounding metal surfaces will be hot and can
cause burns to the skin. Exercise caution to avoid burns.
Maintain oil level as instructed in Engine
Operator’s Manual. Be careful not to spill oil on
any of the belts.
To complete an oil change, proceed as follows:
1.
Run the engine for a short time to warm
the engine oil. The oil will flow more
freely and carry away more impurities.
Use care to avoid burns from hot oil.
2. Locate the oil drain hose on the engine.
See Figure 4-4.
Figure 4-4
3. Remove the hose from the clip securing
it to the frame.
4. Route the free end of the oil drain hose
toward an appropriate oil collection
container with at least a 2.5 quart
capacity, to collect the used oil.
Note: Avoid getting oil on the muffler
when draining.
5. While holding the free end of the
oil drain hose over the oil collection
container, unscrew the square-head
hose plug from the end of the hose. See
Figure 4-4. Drain the engine oil into the
collection container.
6. Remove the oil filter to make sure all the
oil is drained.
7. After draining the oil, wipe any residual
oil from the oil drain hose. Thread the
square head plug into the drain hose
fitting and fully tighten the plug.
8. Replace the oil filter and refill the
engine with new oil as instructed in the
Engine Operator’s Manual. Refer to the
Engine Operator’s Manual for information
regarding the volume and weight of
engine oil.
9. Place the hose back into the clip securing it
to the frame.
Lubrication
Periodically lubricate all pivot points with a
quality lubricating oil.
Tires
Check the tire air pressure after every 50 hours
of operation or weekly. Keep the tires inflated
to the recommended pressures. Improper
inflation will shorten the tire service life and
produce an uneven cut. See the tire side wall
for proper inflation pressures. Observe the
following guidelines:
•
Do not inflate a tire above the maximum
pressure shown on the sidewall of the tire.
• Do not reinflate a tire that has been run
flat or seriously under inflated. Have it
inspected and serviced by a qualified
tire mechanic.
Battery Information
WARNING
Should battery acid accidentally splatter into the eyes or
onto the skin, rinse the affected area immediately with
clean cold water. If there is any further discomfort, seek
prompt medical attention.
If acid spills on clothing, first dilute it with clean water,
then neutralize with a solution of ammonia/water or
baking soda/water.
NEVER connect (or disconnect) battery charger clips
to the battery while the charger is turned on, as it can
cause sparks.
Keep all sources of ignition (cigarettes, matches, lighters)
away from the battery. The gas generated during charging
can be combustible.
As a further precaution, only charge the battery in a well
ventilated area.
Always shield eyes and protect skin and clothing when
working near batteries.
Batteries contain sulfuric acid and may emit explosive
gases. Use extreme caution when handling batteries. Keep
batteries out of the reach of children.
Battery Maintenance
• The battery is filled with battery acid and
then sealed at the factory. However, even a
“maintenance free” battery requires some
maintenance to ensure its proper life cycle.
• Spray the terminals and exposed
wire with a battery terminal sealer, or
coat the terminals with a thin coat of
grease or petroleum jelly, to protect
against corrosion.
• Always keep the battery cables and
terminals clean and free of corrosion.
• Some models are equipped with a
battery containing a liquid electrolyte.
Handle the battery with care and avoid
tipping to prevent leakage.
WARNING
Batteries contain sulfuric acid and may emit explosive
gases. Use extreme caution when handling batteries.
Keep batteries out of the reach of children.
Battery Storage
1. When storing the tractor for extended
periods, disconnect the negative battery
cable. It is not necessary to remove
the battery.
2. All batteries discharge during storage.
Keep the exterior of the battery clean,
especially the top. A dirty battery will
discharge more rapidly.
3. The battery must be stored with a full
charge. A discharged battery can freeze
sooner than a charged battery. A fully
charged battery will store longer in cold
temperatures than hot.