manualshive.com logo in svg

Cub Cadet 450 Series, Operator'S Manual, Page: 19 / 20

Share
Download
Cub Cadet 450 Series Operator'S Manual Download Page 19

19

9

Illustrated 

Parts List

Model 450 

Series

To order replacement 

parts, contact your  

local Cub Cadet dealer; 

or call our dealer  

locator number at  

1 (877) 282-8684; 

or log onto 

www.cubcadet.com 

Ref. Part No.

Part Description

1.

686-0111

Belt Cover Bracket Ass’y

2.

710-0237

Hex Bolt 5/16-24 x .62”

3.

710-0412

Hex Bolt 1/4-28 x .75”

4.

710-0502A Hex Washer Screw 3/8-16 x 1.25”

5.

710-0152

Hex Bolt 3/8-24 x 1.0

6.

710-0599

Hex Washer Screw

7.

710-0723

Hex Cap Screw 3/8-16 x 1.25

8.

712-0266

Lock Jam Nut 3/8-16

9.

712-0267

Hex Nut 5/16-18

10.

714-0104

Internal Cotter Pin 

11.

736-0104

Hairpin Clip

12.

736-0119

Lock Washer 5/16”

13.

736-0176

Flat Washer .25 ID x .93 OD 

14.

736-0271

Spring Washer .317 ID x .625 OD

15.

736-0329

Lock Washer 1/4” ID

16.

736-0452

Bell Washer .396 ID x 1.14 OD

17.

738-0876 

Shoulder Nut 7/16-20

18.

746-1117

Clutch Cable

19.

747-1159

Idler Pulley Rod

20.

754-0434

V-Belt

21.

756-0405

Flat Idler w/Flange 3.75 OD

22.

756-0971

Outer Engine Pulley Half

23.

756-0972

Inner Engine Pulley Half

24.

756-1162

Input Pulley

Ref. Part No.

Part Description

25.

786-0064A Idler Bracket

26.

786-0185

Belt Keeper Bracket 

27.

786-0187

Shift Cover Bracket

28.

786-0193

Idler Belt Keeper

29.

634-04231

Wheel Assembly 16.0 x 4.6 x 8

734-0808

Tire Only 16.2 x 4.6

30.

634-04230

Wheel Rim Assembly

31.

734-0255

Air Valve 

32.

710-0606

Hex Head Screw 1/4-20

33.

712-04064

Flange Lock Nut 1/4-20

34.

710-0515

Hex Bolt 1/2-20 x 3.50

35.

712-3066

Hex Nut 1/2-20

36.

686-0192

Bumper Assembly

37.

736-0326

Flat Washer 

38.

736-0921

Lock Washer 1/2

39.

710-0653

Hex Screw 1/4-20 x .375

40.

710-1017

Screw 1/4-14 x .625

41.

712-0392

Lock Nut

42.

736-3020

Flat Washer .271 ID x .630 OD

43.

784-0158A Belt Cover

44.

736-0242

Bell Washer .340 ID x .872 OD

45.

737-0298

Straight Pipe 1/4-3.5”

46.

737-0132

End Cap

NOTE:

 For painted parts, please refer to the list of 

color codes below.  Please add the applicable color 
code, wherever needed, to the part number to order a 
replacement part.  For instance, if a part numbered  
700-xxxx is painted Cub Yellow, the part number to 
order would be 700-xxxx-0716.

 

 

Cub Yellow: 0716

 

 

Powder Black: 0637

Summary of Contents for 450 Series





















Reviews:

No comments