Cub Cadet 29HP Tank 53AB5GFZ750 Operator'S And Service Manual Download Page 4

4

GENERAL SAFETY
OPERATIONS

A. DANGER

1.

Do not operate machine in confined areas 
where exhaust gases can accumulate.

2.

Do not operate machine without mower chute 
deflector in place and operational.

3.

Do not carry passengers.

B. WARNING

1.

Do not operate machines under the influence 
of alcohol or drugs.

2.

Do not operate machines without all guards 
and safety devices in place and functional.

3.

Do not start machines if there are fuel or oil 
leaks or spillage — clean it up.

4.

Do not operate machines near spilled or leak-
ing fuels.

5.

Do not stop or park machine over dry leaves, 
grass, debris, etc. that could be combustible.

6.

Use extreme care when backing up.

7.

Do not operate machine on slopes greater 
than 15 degrees (27%), and always go across 
slopes, not up and down.

8.

Do not operate machines on slopes when 
traction is reduced (wet grass, ice, soft 
ground, loose ground, leaves, pine needles, 
debris, etc.).

9.

Avoid turning downhill if possible, go slowly 
and use extra care when turning downhill.

10. Do not operate machines during reduce visi-

bility (low light, fog, rain, etc.).

11. Do not operate machines with non-approved 

attachments.

12. Do not operate machines that are dam-

aged.....have machine repaired.

13. Do not operate machines that have not been 

properly maintained.

14. Use only replacement parts that are the same 

or equivalent to the original equipment.

15. Do not modify machines or any of their com-

ponents, especially the engine governor!

16. Do not operate machine for more than 2 hours 

without hearing protection.

C. CAUTION

1.

Use proper protective equipment when oper-
ating machine (gloves, boots, and hearing 
protection are recommended).

2.

Read entire machine Operator’s Manual.

3.

Make sure operators are fully trained in the 
safe use of the machine.

4.

Follow all safety instructions when using the 
machine.

5.

Keep all safety signs legible and properly 
installed.

6.

Do not check for hydraulic leaks with any part 
of the body.

7.

Do not add fuel to a machine when the engine 
is running and/or the exhaust system is hot.

8.

Keep machine clean and free of debris, grass, 
leaves, oil, grease, etc.

9.

Place lap bars in neutral/start position, set 
park brake, disengage P.T.O., turn engine off, 
and remove ignition key before you dismount 
from machine.

10. Use machines laterally or diagonally across 

slopes, avoid going downhill when possible.

11. Go slowly and use extra care when descend-

ing slopes.

12. Disengage P.T.O. when crossing surfaces 

such as asphalt, concrete, loose ground, 
sand, gravel, etc.

13. Use extra care when loading and unloading 

machines from trucks or trailers.

SAFETY PRECAUTIONS

A. General

1.

Read this Operator’s Manual before starting 
the mower. Study the controls and learn the 
proper sequence of operation.

2.

Do not allow anyone to operate or maintain 
this machine who has not read this manual. 
Never permit children to operate this machine.

3.

Never carry passengers.

4.

Do not remove any shields, guards or safety 
devices. If a shield, guard or safety device is 
damaged or does not function, repair or 
replace it before operating the mower.

5.

Always wear safety glasses and safety shoes 
when operating or maintaining this mower. Do 
not wear loose-fitting clothing.

6.

Disconnect the spark plug wires and remove 
the key from the ignition to prevent the engine 
from accidentally starting before performing 
any maintenance on this mower.

7.

Never run the engine indoors without ade-
quate ventilation. Exhaust fumes are deadly.

8.

To avoid serious burns, do not touch the 
engine, exhaust pipe or muffler while the 
engine is running or until it has cooled after it 
has been shut off.

9.

The liquid in the battery is dilute sulfuric acid. 
Always wear safety glasses and rubber gloves 
when working on the battery. Do not overfill 
the battery.

10. Lead-acid batteries generate hydrogen and 

oxygen gases which form an explosive mix-

Summary of Contents for 29HP Tank 53AB5GFZ750





























Reviews: