background image

8

Pairing of Sensor and Cooker Guard Relay 

The Mkomfy set with sensor and cooker guard relay in the same pack are 
already paired. If you have bought a separate sensor, this must be paired 
with the cooker guard relay. This can be done in two different ways. 

Read through the whole instruction for both alternatives before performing pairing!

Alternative 1: 

Pairing of Sensor without physical intervention on cooker guard relay.

1. 

Activate Sensor in pairing mode by setting DipSW 4 to active [ON]. 

2. 

Disconnect the power to the cooker guard relay for 5 seconds by 
turning the relevant fuse circuit off and on.  
- Within 20 seconds of turning the fuse circuit on:  
 

Hold in the function button on the sensor for 6 seconds.  

The sensor will emit a sound signal every 2 seconds, if pairing 
has succeeded.

3. 

Once again, disconnect the power to the cooker guard relay 
for 5 seconds by turning the relevant fuse circuit off and on. 

 

NB! This must be done within one minute of connecting the 

relay under Point 2, or the pairing will not be saved

4. 

Set DipSW 4 back to inactive [OFF].

  

Pairing is now complete.

Alternative 2: 

Pairing of Sensor by activation of programming button on cooker guard relay.

1. 

Activate Sensor in pairing mode by setting DipSW 4 to active [ON].

2. 

Briefly press the programming button on the cooker guard relay. 
Yellow diode will now begin to flash. The cooker guard relay will 
now be in pairing mode for 30 seconds. 

3. 

Hold in the function button on the sensor for 6 seconds while 
the yellow LED flashes. The sensor will emit a sound signal every 
2 seconds, if pairing has succeeded. 

4. 

Set DipSW 4 back to inactive [OFF].

NB: It is not possible to have more than 1 Mkomfy Sensor connected to the 
Cooker Guard Relay at the same time. Pairing a new sensor will automatically 
delete the sensor already paired with the cooker guard relay. 

Installation information

Summary of Contents for Mkomfy R-T 25A













Reviews: