manualshive.com logo in svg

CTC Union VRM01/24, User Manual

Share
Download
CTC Union VRM01/24 User Manual Download Page 28

VDSL SERIES 

 

 

 

CTC Union 

 

           

 

26 

4-4-4. Port Controls 

This page can change every port status. 

1.State: 

User can disable or enable this port control. 

2.Auto Negotiation: 

User can set auto negotiation mode is Auto, Nway (specify the 

speed/duplex on this port and enable auto-negotiation), Force of per port. 

3.Speed: 

User can set 1000Mbps, 100Mbps or 10Mbps speed on Port25~Port26 (base on 

copper mode, if Fiber mode force on 1000Base-FX). 

4.Duplex: 

User can set full-duplex or half-duplex mode of per port. 

5.Flows control: Full: 

User can set flow control function is enable or disable in full mode. 

Half: 

User can set backpressure is enable or disable in half mode. 

6.Rate Control: VRM01/24

, port1 ~ port 24, supports by-port ingress and egress rate control. 

For example, assume Port 1 is 10Mbps, users can set it’s effective egress rate is 1Mbps, ingress 
rate is 500Kbps. VRM01/24 will be performed 
flow control or backpressure to confine the ingress rate to meet the specified rate. 

Ingress: 

Type the port effective ingress rate. The valid range is 0 ~ 100. The unit is 100K 

0: disable rate control. 
1 ~ 100: valid rate value (100=10Mbps) 

Egress: 

Type the port effective egress rate. The valid range is 0~100. The unit is 100K. 

0: disable rate control. 
1 ~ 100: valid rate value. 

7.Port Security: 

A port in security mode will be “locked” without permission of address learning. 

Only the incoming packets with SMAC already existing in the address table can be forwarded 
normally. User can disable the port from learning any new MAC addresses, and then use the 
static MAC addresses screen to define a list of MAC addresses that can use the secure port. 
Enter the settings, then click Apply button to changes on this page. 
 

 

Summary of Contents for VRM01/24


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands