CTC Union IPM-4SE, User Manual

Page: 17 / 26

Chapter 3 Configuration and Operation
17
CLI Command Descriptions
Provisioning Commands
gci
Initialize GCI Middle Ware & CESoPSN chip
Initialize relative Tasks, Messages and Semaphores.
CAUTION: This will clear all the configuration.
cesopget Get current CESoPSN Setting.
srcnet ip_addr net_mask gateway_ip
Set CESoPSN IP address, net mask and gateway IP address.
ip_addr: IP Address, net_mask: net mask, gateway_ip: gateway IP.
EX: srcnet 192.169.1.28 255.255.255.0 192.169.1.254
lanset enable bandwidth
Set CESoPSN LAN Traffic Enable and Bandwidth.
enable: 0:disable, 1: enable.
bandwidth: 0~15 (0: 50K, 1:100K, 2:150K, 3:200K, 4:250K, 5:300K, 6:350K, 7:400K,
8:800K, 9:1.6M, 10:3.125M, 11:6.25M, 12:12.5M, 13:25M, 14:50M, 15:100M)
EX: lanset 1 15 (use the rest of BW minus TDM traffic)
vlanset enable Set Vlan Mode enable/disable
ceschset ch_no enable dest_ip dest_mac
Set CESoPSN Channel Enable, Destination IP and MAC.
ch_no: E1 channel number (1~4)
enable: 0:disable, 1: enable.
dest_ip: destination node IP address.
dest_mac: destination node MAC address
Situation 1: Set dest_ip, then get dest_mac from far end
EX: ceschset 1 1 192.168.1.28
Situation 2: Set dest_ip and dest_mac manually
EX: ceschset 1 1 192.168.1.28 AA:BB:CC:DD:EE:FF
cespwidset ch_no TrPWID PrPWID
Set CESoPSN Channel TrPWID and PrPWID.
ch_no: E1 channel number (1~4)
TrPWID: Transmit PseudoWire ID.
PrPWID: Provision PseudoWire ID.
EX: cespwidset 1 1 1
jitterbd ch_no depth
Set CESoPSN Channel Jitter Buffer Depth. Initial Jitter DS is 3.
ch_no: E1 channel number (1~4)
depth: jitter buffer depth 0~7 (0:11ms, 1:23ms, 2:40ms, 3:75ms, 4:99ms, 5:145ms,
6:192ms, 7:239ms)
EX: jitterbd 1 2 (Suggested default is to set 40 ms for general uplink latency)
pktsize ch_no pkt_size
Set CESoPSN Channel Packet Size
Pkt_size: 0: 1514 Byte, 1: 782 Byte, 2: 178 Byte. 3: 306 Byte.
cesfe1mode ch_no enable
cesfe1crc ch_no enable
cesfe1tsmap ch_no TsMap
eberset ch_no enable threshold
Set CESoPSN EBER Enable and Threshold.
ch_no: E1 channel number (1~4)
enable: 0:disable, 1: enable.
threshold: 0 ~ 3 (0:10^ ‐ 3, 1:10^ ‐ 4, 2:10^5, 3:10^ ‐ 6)
ceschtgpriset ch_no 1st.source
2nd.source
Set CESoPSN Channel clock priority source in TG mode
Source: 1:E1.TG, 2:HoldOver, 3:FreeRun.
ceschvlanvlpid ch_no vlp id
Set CESoPSN Channel vlan tag
vlp:0 ~ 7, id: 0 ~ 0xFFF
eberget Get CESoPSN EBER Enable and Threshold.
Alarm Command
almall Display all alarm status (CESoPSN)
Table 3.1 CLI Command Descriptions