CTA PAD-SHFS, Instruction Manual

Page: 2 / 7

2.Stand Assembly:
1. Insert the pole into the center of the heavy duty base.
2. Place metal washer over tightening screw rod, then screw into the
bottom side of the stand base center, turning clockwise to tighten.
METAL CONNECTION
HEAVY DUTY BASE
HEIGHT
ADJUSTMENT
KNOB
POLE
METAL WASHER &
TIGHTENING SCREW ROD
Attaching wheels:
Connect wheels to stand base before attaching pole.
Screw wheels into floor base by hand,
then use wrench to tighten.
Instructions:
Use this table to determine the appropriate
foam pad to use with your tablet.
Note : sizes refer to total tablet size with or
without a case.
m
m
Foam Pad
Thickness
Tablet
Thickness:
1mm 0.67-1.06in
5mm 0.51-0.91in
10mm 0.31-0.71in
17-27m
13-23m
8-18mm
/
/
/
1.Attaching Foam Pad to Tablet Holder
Select the appropriate foam pad according
to the thickness of your tablet (or tablet in its
case), then press adhesive side into center
of the tablet holder.
1mm Foam Pad
5mm
Foam
Pad
10mm
Foam
Pad
LOCK
UNLOCK
LOCK
UNLOCK
LOCK
UNLOCK
LOCK
UNLOCK
LOC
K
UNLOCK
1. Insert key and set position
to unlock. Remove key,
then slide holder open.
2. Load tablet corner first
into one end. Insert key
and set to lock, then slide
holder shut until secure.
Remove key.
Section 1
loosen completely and remove from top
PAD-SCGS
3. Base Assembly and Connecting the Metal Cover:
METAL CONNECTION
HEIGHT
ADJUSTMENT
KNOB
POLE
METAL
CROSS BASE X 2
CONNECTION SCREW BOLT,
WASHERS AND NUT
Pole Assembly and Pole Nut
Cross Base Sections (2)
Allen Key
2. Installing the Wheels
Wheel
Place a spring washer over the screw
bolt on the wheel.
Place the screw bolt from each wheel through the metal base, then place a nut cover
over the top of each. Screw down clockwise by hand, then use wrench to tighten
further.
Screw Nut Cover
Spring
Washer
Metal
Base
1) Place the metal base pieces with the higher
piece on top of the cross base. Align the holes
at the bottom of the pole with the holes on the
cross base.
2) Insert a screw bolt with a washer into each
of 4 holes. Place another washer on the
underside of each screw bolts.
3) Grip the nut on the underside with one hand,
and use the other to tighten each screw with
the Allen key. Repeat to tighten all four
screw bolts.
4. Rotate the grip counter clockwise to
of pole. 5. Place the square metal cover over
the top of the pole and slide down to
stand base.
6. Place grip back over stand pole
and tighten.
4. Connecting the Tablet gooseneck holder & Battery Case
3. Rotate plastic grip counter clock-
wise to loosen, then adjust pole to
desired height. Rotate plastic grip
clockwise to tighten.
1. Refer to Section 1 to install your
device and make sure you have held
it securly.
2. Tighten and loosen the gooseneck to
holder connection screw to adjust ease of
rotation.
5. Installing your Device and Adjusting the Floor Stand:
3. Turn the Y screw clockwise to
tighten the connection.
Gooseneck
Metal
Connection
Y Screw
Battery Case
1. Place battery case over top of
metal connection.
Note: if Y screw is already in,
unscrew before attaching gooseneck.
2. Screw the gooseneck onto the
metal connection of the pole by
turning clockwise. Be sure that the
battery case is on the opposite side
of the pole as the Y screw.
Allen Key
Instructions:
Use this table to determine the appropriate
foam pad to use with your tablet.
Note
: sizes refer to total tablet size with or
without a case.
m
m
Foam Pad
Thickness
Tablet
Thickness:
1mm 0.67-1.06in
5mm 0.51-0.91in
10mm 0.31-0.71in
17-27m
13-23m
8-18mm
/
/
/
1.Attaching Foam Pad to Tablet Holder
Select the appropriate foam pad according
to the thickness of your tablet (or tablet in its
case), then press adhesive side into center
of the tablet holder.
1mm Foam Pad
5mm
Foam
Pad
10mm
Foam
Pad
LOCK
UNLOCK
LOCK
UNLOCK
LOCK
UNLOCK
LOCK
UNLOCK
LOCK
UNLOCK
Package Contents:
1.Insert key and unlock the
holder,TAKE OUT THE KEY
then slide the arm to open
to a width according to your
need.
2. Insert key and lock the
holder,TAKE OUT THE KEY
then install your device in
and slide the arm closed
to hold tightly.
Section 1
3. Rotate plastic grip counter clock-
wise to loosen, then adjust pole to
desired height. Rotate plastic grip
clockwise to tighten.
1. Refer to Section 1 to install your
device and make sure you have held
it securly.
2. Tighten and loosen the gooseneck to
holder connection screw to adjust ease of
rotation.
3. Installing your Device and Adjusting the Floor Stand: