background image

 

 

Page 7-C 

6.2.  Configuration Settings 

6.2.1. 

 Select Menu Icon, settings and then navigation 

6.2.1.1. 

Configure how you want to navigate your controller using drop-down window menu (similar to 

previous CSZ controllers) or slide-navigation using icons like a smartphone.  Setting may be 

changed at any time. 

 

6.3.  Running Chamber Without a Profile 

 

6.3.1. 

Touch the red “SP” box and enter a 

temperature set-point. 

6.3.2. 

Touch the “Manual Operation” to access the 

on/off switches menu. 

6.3.3. 

Touch the toggle switch next to “CHAMBER” 

to toggle from “OFF” to “ON”. 

6.3.4. 

Touch “Done” to close the “switches” menu 

and set the changes made. 

6.3.5. 

To set a relative humidity set-point follow the 

above process using the grey “%” box and 

the “HUMIDITY” toggle switch. 

 

6.4.  Using Guaranteed Soak (G-Soak) Event 

 

6.4.1. 

The G-Soak selection for a profile is a tool that allows the user to guarantee timed soaks with-in 

specified limits for the event selected. 

6.4.2. 

The G-Soak selections are used to turn on the guaranteed soak option for one or more of the 

control loops.  To enable guaranteed soak for a loop, first press the ‘G-Soak’ button above the 

event list view on the Program Entry screen. This will display the list of soak selections for each 

loop of the chamber

6.4.3. 

Press the on/off button for a loop to toggle the guaranteed soak selection on and off as desired.  

When the guaranteed soak event for a loop is turned on, the program will automatically enter a 

hold condition during the step if the loop’s PV deviates from its set point by more than the soak limit 

setting for the loop as entered on the G-Soak Limits screen.

 

 

Guaranteed soak should not be used on ramping steps.  The ramp rate will be affected if the 

process variable deviates from the soak band because the program will be placed in hold.  When 

the program is in hold, the step length will be extended and the set points will no longer ramp at the 

desired rate.  Guaranteed soak should be used on soak steps to make sure that the process stays 

at the desired set point, within the soak band, for the full time duration of the step.

 

 

Summary of Contents for Z-Plus














Reviews: