background image

INSTALLATION MANUAL

 

 

Southern Glass Green Energy Industrial Park, 

                                                                                               Xinji Village, Machong Town, Dongguan, China. 

Tel: 86-769-88288015   Fax: 86-769-88288160 

www.csgpvtech.com

 

 

 

 

 

 

 

I. INTRODUCTION

 

 

 

 

 

 

This manual contains information of electrical and mechanical installation and safety information which you should 
know before using 

CSG270M2-35/1956

х

992

 series

CSG230M2-30/1640×992

 series

CSG205M2-26/1482×992

 series

 

CSG180M2-24/1324×992

 series 

and 

CSG135M2-17/1482×674

 series

 photovoltaic modules. This manual will show you how 

  to install the Photovoltaic Module. 

 

Please read carefully this manual thoroughly before starting the installation. 

 

The information in this manual is described on the basis of CSG PVTech’s knowledge and experience.    But such 
information and suggestions do not constitute a warranty. CSG PVTech reserves the right to make changes to the 
product, specifications, or to the manual without prior notice. 

 

II. APPEARANCE

 

The appearances and dimensions of the modules are as follows: 

 

Series 

Power of each module 

Dimensions 

Fig. NO.

CSG270M2-35/1956

х

992 

280W

275W

270W

265W

260W

255W

250W 

1956mm(L) x 992mm(W)x 50mm(H) 

Fig. 1-a 

CSG230M2-30/1640×992 

230W

225W

220W

215W

210W 

1640mm(L) x 992mm(W)x 45mm(H) 

 

CSG205M2-26/1482×992 

205W

200W

195W

190W

185W 

1482mm(L) x 992mm(W)x 45mm(H) 

 

CSG180M2-24/1324×992 

180W

175W

170W

165W

160W 

1324mm(L) x 992mm(W)x 45mm(H) 

 

CSG135M2-17/1482×674 

135W

130W

125W

120W

115W 

1482mm(L) x 674mm(W)x 45mm(H) 

 

 

Each module has eight 8mm diameter mounting holes at the aluminum frames using for fixed the modules to the 
supporting structure. There is one terminal box installed on the back of module, two cables were lead out from the 
box and with a connector at the end of each cable. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Fig. 1-a

   

CSG270M2-35/1956*992 series

 solar module 

Summary of Contents for CSG135M2-17/1482x674 series












Reviews: