Crytec D30MB Original Instruction Download Page 15

MINI TRACKED DUMPER

14

GB

Operation

The engine is shipped without oil. Do 
not start the engine before adding oil. 
Please refer to your engine manual 
for the proper grade of oil to add.

DO NOT OVERFILL. Check engine 
oil level daily and add as needed.

Gasoline is highly flammable and 
explosive. You can be burned or 
seriously injured when handling fuel. 
Use extreme care when handling 
gasoline.

Fill the fuel tank outdoors, never 
indoors. Gasoline vapors can ignite 
if they collect inside an enclosure. 
Explosion can result.

IMPORTANT: DO NOT OVERFILL!

This equipment and/or its engine 
may include evaporative emissions 
c o n t r o l   s y s t e m   c o m p o n e n t s , 
r e q u i r e d   t o   m e e t   E P A   a n d /
or CARB regulations, that will 
only function properly when the 
fuel tank has been filled to the 
recommended level. Overfilling 
may cause permanent damage 
to evaporative emissions control 
system components. Filling to 
the recommended level ensures 
a vapor gap required to allow for 
fuel expansion. Pay close attention 
while filling the fuel tank to ensure 
that the recommended fuel level 
inside the tank is not exceeded. Use 
a portable gasoline container with 
an appropriately sized dispensing 
spout when filling the tank. Do not 
use a funnel or other device that 
obstructs the view of the tank filling 
process.

Never use choke to stop engine.

Clutch Control Lever

Squeeze the control lever, clutch engaged. 
Release the lever, clutch disengaged.

Make sure the power trackbarrow is on a 
flat, level surface.

Open the fuel shut-off valve.

 

Move the engine switch to the ON position.

Using a funnel, add oil up to the FULL mark 
on the dipstick. (See engine manual for oil 
capacity, oil recommendation, and location 
of fill cap.)

Reinstall the fuel cap and tighten. Always 
clean up spilled fuel.

Remove the oil fill cap/dipstick to add oil.

1. 

2. 

1. 

3. 

3. 

2. 

Add Oil To Engine

Add Gasoline To Engine

CLOSED

OPEN

Starting Engine

ON

OFF

ON

OFF

 The engine must be off and allowed to cool 
at least two minutes before adding fuel.

Remove the fuel filler cap and fill the tank. 
(See engine manual for fuel capacity, fuel 
recommendation, and location of fuel cap.)

1. 

2. 

Summary of Contents for D30MB






























Reviews: