Crystal Vision Indigo TANDEM 320 User Manual Download | Manualshive

Page: 12 / 62

background image

Crystal Vision

Rear modules and signal I/O

3 Rear modules and signal I/O

The 2U Indigo 2 frames will house up to 12 single height modules and dual power supplies.
The 1U Indigo 1 frames will house six single height modules and a single or dual power
supply. The Indigo DT desk top boxes have a built-in power supply and will house up to two
single height modules. All modules can be plugged in and removed while the frame is
powered without damage.

Note

:

For details of fitting rear connectors please refer to the appropriate frame manual.

TANDEM 320 can support the following rear modules: RM71 and RM72.

Rear module connections with RM71

The RM71 being a single height module will allow maximum packing density with the
maximum number of outputs available. Eight channels of audio AES stereo pairs or eight
mono analogue channels are presented as balanced I/O on the 26-way high density D-Type
connector.

RM71 rear module connector

Description

RM71

•

12 per Indigo 2 frame

•

Six per Indigo 1 frame

•

Two per Indigo DT

•

All frame slots can be used

BNC connections

BNC

I/O assignment

HD/SD IN 1

3G/High Definition/Standard Definition serial digital input channel A

HD/SD IN 2

3G/High Definition/Standard Definition serial digital input channel B

HD/SD OUT 1

3G/High Definition/Standard Definition serial digital output channel A

HD/SD OUT 2

3G/High Definition/Standard Definition serial digital output channel B

26-way D-Type Audio Connections

The 26-way audio ‘D’ connector RM71

module can be used for analogue or digital, inputs or

outputs – or a mixture of both depending on the I/O modules fitted. Half of the I/O channels on
the rear module are connected to the front I/O (nearest handle) module position (video
channel A) and the remainder to the rear module position (video channel B). The DIOP4 will
normally be configured as 110 ohm balanced operation when using this rear module.

TANDEM 320 User Manual R1.3

11

11 July 2019

«
...
10
11
12
13
14
...
»

Summary of Contents for Indigo TANDEM 320































































Reviews:

No comments

Related manuals for Indigo TANDEM 320

Brand: NI Pages: 20

Brand: Hamlet Pages: 4

Brand: Gigabyte Pages: 44

Brand: Kontron Pages: 2

Brand: Dynamic Engineering Pages: 46

Brand: MSI Pages: 1

Brand: S-1 Pages: 4

Brand: National Instruments Pages: 64

Brand: Hama Pages: 42

Brand: Axiom Pages: 4

Brand: Virident Pages: 33

ReadEasy Move 2

Brand: VisionAid International Pages: 25

Wireless G ADSL Modem Router

Brand: Hercules Pages: 80

Brand: GeoVision Pages: 4

Brand: Diablotek Pages: 1

Brand: ZALMAN Pages: 16

Brand: APLIC Pages: 16

Brand: IDTECK Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands