TO FACTORY
HARNESS
22-PIN
(male plug)
8-PIN
(male plug)
INTERFACE
22-PIN
(female plug)
4 5 6
TO ENABLE VIDEO
IN-MOTION
1. On = Enable VIM
2. On = Enable R VC
3. Not Used
4. On = Enable Force R VC
5. May Vary
6. May Vary
WHITE
/ 12V OUTPUT
ON
1 2 3
VIDEO-IN
(female plug)
TO FACTORY
RADIO
GREEN
/ 12V POWER SWITCH
22-PIN
(female plug)
22-PIN
(male plug)
WHITE
WHITE
WHITE
GRAY
VIDEO HARNESS
TO CAMERA
work. Following these instructions from “Start” to” Finish” will ensure a
smooth and hassle free installation.
822-1348. We a re he re to help.
PAR TS INCLUDED:
(1) Universal Camera (CUB-01)
(1) 20 ft. Extension
(1) CH-75E Interface (2.1.2)
(1) CH-75E Harness (2644-B)
(1) Instruction
- Lens Angle 170 Degrees
- Resolution 420 TV Lines
- Min. Illumination 0.2Lux
- Voltage 12v
- Operating Temp. -22˚F - 176˚F
- NTSC
- Reference Lines
- Shutter Speed 1/60s - 20us
- Waterproof
- Pixels 656 x 492
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
during the installation.
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
Please read the entire manual before installing this interface.
The force reverse is used to view the back-up camera when the vehicle
is not in reverse gear. Allows you to view what is in the back while
driving.
To activate this feature make sure the
dip switch settings are correct.
Then simply
press the center button
once on the
Left Hand
steering wheel
control.
Note: The camera is defaulted to power
down after 10 seconds.
CHRYSLER:
2011-2015 300 (See Note Below)
DODGE:
2011-2014 Charger
2011-2016 Journey
IMPORTAN T:
Compatible Radio Type:
U-CONNECT 8.4” SCREEN
RVCCH-75E
CONNECTIONS OVERVIEW
TROUBLE SHOOTING
1. No video display while in reverse.
- Make sure the dip switches are in the correct position. More support contact us.
The parking lines are the re to assist you while reversing.
What the lines mean:
Green Line: CLEAR
Yellow Line: GETTING CLOSE
Red Line: WARNING - VERY CLOSE
RED
YELLOW
GREEN
INSTALLING THE CAMERA AND CABLE
REAR-VIEW & VIM INTEGRATION FOR CHRYSLER & DODGE VEHICLES with 2-PIECE RA
DIO
PARKING LINE
U-CONNECT 8.4” SCREEN
(2-PIECE RADIO)
Dip 1:
Activates the Video In-Motion feature. The dip switch
is the permanent solution for keeping the VIM unlocked.
Use the Green wire with a toggle switch for a non-permanent
solution. (Switch not included)
Dip 2:
Activates the Rear-View Camera image when the vehicle is in
reverse gear.
Dip 4:
Activates the “Force Rear-View Camera” while driving.
Force Rear-View Camera allows the driver to view the
rear-view camera when not in the Reverse gear.
Dip 5 & 6:
Varies, these switches are defaulted both to OFF.
If the radio is having turn-on issues please try the following:
Attempt One: Set both 5 & 6 to the ON position.
Attempt Two: Set 5 to On and 6 to OFF.
Attempt Three: Set 5 to OFF and 6 to ON.
If none of the above solutions work out for your vehicle please
contact tech support.
SETTING THE DIP SWITCHES
FORCE REVERSE
PRESS
SEEK UP
SEEK DN
4 5 6
TO ENABLE VIDEO
IN-MOTION
1. On = Enable VIM
2. On = Enable R VC
3. Not Used
4. On = Enable Force R VC
5. May Vary
6. May Vary
ON
1 2 3
INTERFACING SOLUTIONS
This kit includes a universal bullet camera that can be mounted in
it a clean install. Please see page 3 for installation instructions. After
the camera is installed to the desired location, route the power and
video wires towards the radio and make the connections. For powering
the camera, use the 12V OUTPUT (White Wire) from the 8-pin Molex
connector plugged into the interface.
Note: The camera is defaulted to power down after 10 seconds.
rev.080215
On 2015 Chrysler 300 without a separate
CD slot (one piece radio), use Part#
RVCCH-75C. (see radio picture on page 2)
NOTE:
