background image

All Specifications are subject to change

8

ENG

Please read the user's manual carefully before the installation and the first

operation of the amplifier.

SPECIFICATIONS

Output Power RMS

Output Power Max.

Loudspeaker impedance

Frequency Response

Total Harmonic Distortion

Signal-to-Noise Ratio

Input Sensitivity

Input Impedance

Lowpass Filter

Subsonic Filter

Bass Boost

Bass Boost Frequency

Operating Voltage

External Fuse Rating

Dimensions (B x H x L)

GPX2000.1D Class D

1 x 500 W into 4 Ohms
1 x 750 W into 2 Ohms
1 x 1000 W into 1 Ohms

1 x 1000 W into 4 Ohms
1 x 1500 W into 2 Ohms
1 x 2000 W into 1 Ohms

1 – 8 Ohms

20 – 180 Hz (-3 dB)

< 1 % (1 kHz)

> 85 dB

0,2 – 8 V

20 kOhms

40 – 180 Hz @ 12 dB/Octave

10 – 50 Hz @ 12 dB/Octave

0 – 12 dB @ 30 - 80 Hz

30 – 80 Hz

+12 V (9 – 15 V), negative ground

50 A ANL external protection

254 x 46 x 326 mm

WARRANTY

This product meets the current EU minimum warranty requirements, if purchased in countries of the EU. To ensure your warranty

policy keep your original receipt proofing the date of purchase. Any damage to the product as a result of misuse, abuse, accident,

incorrect wiring, improper installation, alteration of date code or barcode labels, revolution, natural disaster, or any sneaky stuff

because someone messed up, repair or alteration out side of our factory or authorized service centers and any thing else you

have done that you should not have done is not covered. This warranty is limited to defective parts and specifically excludes

any incidental or consequential damages connected therewith.

Summary of Contents for groundpounder GPX2000.1D













Reviews: