8.
Replace the joint inserts by inserting them fully into the ends of the rod (See Fig.5), and, with the outside
arc of the rod closest to you, rotate them, so that the flat surfaces are facing downwards (See Fig. 8)
nd, with the outside
arc of the rod closest to you, rotate them, so that the flat surfaces are facing downwards (See Fig. 8)
9.
Check the length is correct by firstly ensuring the wall bracket swivel joints are fully inserted into the wall
brackets (See Fig.4) and then placing the rod in position on the wall brackets. Align the flexible joint pivot
screw holes by either extending or inserting the joints into the tube (See Fig.8), but do not extend the joint
further than the line shown in Fig.5.
9.
Check the length is correct by firstly ensuring the wall bracket swivel joints are fully inserted into the wall
brackets (See Fig.4) and then placing the rod in position on the wall brackets. Align the flexible joint pivot
screw holes by either extending or inserting the joints into the tube (See Fig.8), but do not extend the joint
further than the line shown in Fig.5.
10. Mark the positions of the joint inserts if adjustement has been made and place the rod back onto the flat
surface. Position the alignment guide onto the end of the joint with the flat face of the alignment guide
facing downwards. (See Fig.9) Rotate the joint until it is aligned with the rod and tighten the expansion
joint using the hex head key provided. (See Fig.10) Repeat for the opposite end.
10. Mark the positions of the joint inserts if adjustement has been made and place the rod back onto the flat
surface. Position the alignment guide onto the end of the joint with the flat face of the alignment guide
facing downwards. (See Fig.9) Rotate the joint until it is aligned with the rod and tighten the expansion
joint using the hex head key provided. (See Fig.10) Repeat for the opposite end.
11.
Replace the rod to check the alignment of the flexible joint pivot holes. If adjustment is required, undo the
expansion joint screw by 2 or 3 turns and hit the end of the hex head key with a hammer. This will release
the cone insert allowing correct adjustment to be made. DO NOT FULLY UNWIND THE HEX HEAD
SCREW.
11.
Replace the rod to check the alignment of the flexible joint pivot holes. If adjustment is required, undo the
expansion joint screw by 2 or 3 turns and hit the end of the hex head key with a hammer. This will release
the cone insert allowing correct adjustment to be made. DO NOT FULLY UNWIND THE HEX HEAD
SCREW.
12. Slide the wall bracket covers and the ball covers onto the rod, noting their orientation (See Fig.11) Place
the O-ring over the end of the joint and locate it into the annular recess. (See Fig.12)
12. Slide the wall bracket covers and the ball covers onto the rod, noting their orientation (See Fig.11) Place
the O-ring over the end of the joint and locate it into the annular recess. (See Fig.12)
13.
Assemble the rod to the wall bracket swivel inserts ensuring the curve of the rod is pointing into the room.
Place the plastic bush between the two halves of the flexible joint and screw tightly together. (See Fig.13 &
14)
13.
Assemble the rod to the wall bracket swivel inserts ensuring the curve of the rod is pointing into the room.
Place the plastic bush between the two halves of the flexible joint and screw tightly together. (See Fig.13 &
14)
14.
Once the rod is in position carefully slide the ball cover over the flexible joint assembly until it engages with
the O-ring. Slide the wall bracket cover over the wall bracket, aligning the two tabs at the back of the cover
with the two recesses in the wall bracket. (See Fig.16 & 17) Twist the cover clockwise to secure in
position. (See Fig.16)
14.
Once the rod is in position carefully slide the ball cover over the flexible joint assembly until it engages with
the O-ring. Slide the wall bracket cover over the wall bracket, aligning the two tabs at the back of the cover
with the two recesses in the wall bracket. (See Fig.16 & 17) Twist the cover clockwise to secure in
position. (See Fig.16)
15.
Hook the Rod Reacher onto the rod and rotate the rod to check the assembly is working correctly.
15.
Hook the Rod Reacher onto the rod and rotate the rod to check the assembly is working correctly.
R&R 038 R01
Product Care Advice
To retain the best quality finish, clean product regularly with a
soft damp cloth. Do not use abrasive or chemical cleaners, as
these will damage the product.
Please retain this leaflet for future reference.
Croydex Ltd, Central Way, Andover, Hants, SP105AW, UK
Tel: +44 (0) 1264 365881 ~ Fax: +44 (0) 1264 356437
website:
~ Email: info@croydex.co.uk