background image

SET-UP

Prior to use

damage.

 i

Gas-Pro orientation

Figure 1: Gas-Pro 

 

 

À

 D-ring  

Ã

 Operator button 

Æ

Á

 Alarm bars 

Ä

 Sensor apertures 

Ç

 

Â

 Sounder 

Å 

Pump inlet/outlet 

È 

DISPLAY

 Home Screen

 

• 

to 5 gases.

• 

recognition of alarm events.

• 

• 

the gas in alarm.

Â

Å

À

Æ

Ä

Ã

Á

OPERATION

Switching On/Off

• 

In clean air turn on the Gas-Pro by holding down the operator button 

for 3 audible blips. The Gas-Pro will warm up, going through a series of 

automatic processes.

• 

To turn off, press and hold the operator button. During the 4 second 

countdown hold the button down until the countdown has finished. 

 Quick View 

• 

A momentary press of the operator button allows the user to see the gas 

type and unit, battery level, user and +ve Safety™ status.

Alarms

• 

Gas-Pro offers audible, visual and vibrate alarms as standard.

• 

Each gas has 2 instantaneous alarms and toxics also have TWA alarms.

• 

When in alarm the display backlight will change from green to red and 

highlight the gas in alarm.

• 

When the Gas-Pro warns of a low battery, the sounder will emit an audible 

double blip every 5 seconds and the +ve Safety™ LED will go red. This 

means the battery has at least 30 minutes of battery life remaining. After 30 

minutes the Gas-Pro will enter full alarm state and the battery icon will flash 

empty as shut down is imminent.

Backlight

• 

The backlight is configurable but set as standard to come on at the press 

of the operator button or during alarm.

Pump

• 

If the internal pump option has been chosen, the pump is activated by 

attaching the pumped flow plate. 

• 

Ensure the gasket is clean and undamaged prior to placement. 

• 

The pump test will activate every time the flow plate is attached the user 

will be prompted to cover the inlet to ensure a tight seal. Gas-Pro will 

indicate a pass or fail, if failed the flow plate should be removed, checked 

and reapplied. 

3

www.calcert.com

[email protected]

1.800.544.2843

0

5

10

15

20

25

30

Summary of Contents for Gas-Pro







Reviews: