SETTING UP THE DETECTOR
Switch 4 – Marked M - MW SENSITIVITY Setting
Used for setting the MW functions in order to provide
MW sensitivity control according to the environment.
**
ON Position (Up)
- Low sensitivity, for harsh
environments.
Testing the Detector - WALK TEST
Upon installation, the unit should be thoroughly tested
to verify proper operation.
Apply 12 Vdc power to the detector, wait 2 minutes to
J4
2/4 MODE
EOL TAMPER 2/4
J5
J4
1 2 3 4
EOL ALARM
1 2 3 4
P/N3203974
PIR
J3
L P W M A
OFF Position (Down)
- High sensitivity, for normal
operation - immediate detection.
Switch 5 – Marked A – AND/OR Mode
Used for setting the ALARM indication mode
**
ON Position (Up)
– AND mode, Alarm will activate
upon PIR
AND
MW detection.
OFF Position (Down)
– OR mode, Alarm will activate
upon PIR
OR
MW detection.
** Note: Marked (**) positions are the factory default
setting of the detector.
RANGE ADJUSTMENT
“MW” POTENTIOMETER
- adjustments according to
protected area range - see fig.5&6.
The potentiometer at mid-scale is equivalent to a
distance of 15m, at min-scale - 7m.
Rotate the potentiometer clockwise to increase range,
counter-clockwise to decrease range.
Dimension change according to installation
location and room size.
“
PIR” POTENTIOMETER
- adjustment according to
finish the detector warm up time. Conduct testing with
the protected area cleared of all people.
Walk test
1. Remove front cover.
2. Make sure that
PIR and MW
switches are in
positions high sensitivity.
3. Make sure that
LED
switch is
ON
.
4. Replace the front cover.
5. Start walking slowly across the detection zone.
6. Observe that the detector
’
s LED lights whenever
motion is detected.
7. Allow 5 sec. between each test.
8. After the walk test is completed, the
LED, PIR and
MW
switches may be changed.
NOTE: Walk tests should be conducted, at least
once a year, to confirm proper operation and
coverage of the detector
Visible Light Filter Option
Use the optional white light filter in order to improve the
detector stability to high intensity visible light.
T
he dip switch selector mounted on the unit’s pc
board controls the functions setting of the detector:
Switch 1 – Marked L - LED Enable
Used for setting LED Enable / Disable
**
ON Position (Up)
– all LED's enabled.
OFF Position (Down)
– all LED's disabled.
Note: the state of the switch “LED” does not affect the
operation of the ALARM and TROUBLE relays
Switch 2 – Marked P - PIR SENSITIVITY Setting
Used for setting the PULSE count function in order to
provide PIR sensitivity control according to the
environment.
**
ON Position (Up)
- High sensitivity for stable
environments, One motion event trips the PIR.
OFF Position (Down)
- Low sensitivity for harsh
environments, Two motion events trip the PIR.
Switch 3 – Marked W - PET IMMUNITY Setting
Used for setting the PET Immune function 12Kg or
25Kg, depending on the pet Weight.
**
ON Position (Up)
- Immunity to an animal up to
12kg
OFF Position (Down)
- Immunity to an animal up to
25kg
EOL Connection Options
The End-Of-Line connection options are described in
the following drawings.
Set
J4 JUMPER “2/4”
according to connection option
Set
J5 “REOL” and J3 “RAL” Jumpers
according to
EOL resistors value (see fig. 3)
Option A - 4 Wire Connection with EOL
protected area range - see fig.5&6.
Use the Potentiometer marked “PIR” to adjust the
detection sensitivity between 30% and 100%, according
to walk test in the protected area.
Rotate the potentiometer clockwise to increase range,
counter-clockwise to decrease range.
After adjusting the sensitivity perform a walk test to
verify optimum correct sensitivity in the protected area.
LED VISUAL INDICATIONS
There are three LED's on the unit’s PC board to signal
various detector events
Option B - Connecting single detector with 2 wire and EOL resistors
Option C - Connecting multiple detectors with 2 wire and EOL resistors
TECHNICAL SPECIFICATION
Detection Method
PIR & Microwave pulse Doppler
Detection Range
2 ~ 15m @ H=1.8 ~ 2.4m
MW Freq. - X Band
10.525GHz / 10.687GHz / 9.9 GHz
Power Input
9.6 to 16
Vdc
Current Draw
Active:
35mA
(+/- 5%)
Standby:
22mA
(+/- 5%)
Temp Consumption
Yes
Alarm Period
2
±
1 sec
Form C - NC&NO
STANDARDS COMPLIANCE
European Council Directive 2004/108/EC
EN50130-4+A1+A2
EN301489-3
EN301489-1
EN61000-6-3
EN50130-5
EN50131-1
EN50131-2-4
EN50131-6
SAFETY LVD 2006/95/EC
CROW ELECTRONIC ENGINEERING LTD.
CROW ELECTRONIC ENGINEERING LTD.
12 Kineret St.
Airport City, 70100 Israel
Tel. +972 3 9726000
Fax. +972 3 9726001
[email protected]
[email protected]
www.thecrowgroup.com
CROW LATIN AMERICA USA INC.
7200 NW 19 st.
Alarm Outputs
28Vdc 0.1 A with 10 Ohm
series protection resistors
EN60950-1 (93/68/EEC)
Security Grade 2, Environmental Class II
Suite 307
Miami FI 33126, USA
Tel. +305 513 4001
AM / Trouble Output
Form A N.C 28Vdc 0.1 A with
10 Ohm series protection resistors
open when cover is removed
N.C 28Vdc 0.1 A with 10 Ohm
For more detailed instruction please refer the manuals
which you could download from the internet at:
www.thecrowgroup.com
Fax. +305 513 4005
[email protected]
www.crowlatinamerica.com
ARROWHEAD ALARM PRODUCTS
Tamper Switch
series protection resistors
open when cover is removed
344B, Rosedale Road
Park Farm Industrial Estate
Albany, Auckland
Warm up Period
1min
Operation Temp
-10
º
C ~ +50
º
C (14
º
F~122
º
F)
Dimensions
116 mm x 60mm x 37mm
Weight
105gr.
N345
P/N 7101740 Rev C YS
New Zealand
Tel. +64 9 414 0085
Fax. +64 9 414 0088
www.aap.co.nz
These instructions supersede all previous
issues in circulation prior to March 2012.
For warranty policy and conditions please refer to CROW ELECTRONIC ENGINEERING Ltd. - WARRANTY POLICY CERTIFICATE on www.thecrowgroup.com
(3)
Insert the FILTER into
the two slots at lens
housing corners
(4)
To fit lens press it into
the cover from the front
until "CLICK" is heard
Event
Message
RED
GREEN
YELLOW
Initial warm-
up (60Sec.)
No Detection
Standby
PIR walk-test
detection
2Sec
MW walk-test
detection
2Sec
ALARM
2Se c
Note: The detector should be reset after any change
by removing and applying the 12V power supply.
BLOCK
TERMINAL
TIN TOUT TEOL AIN AOUT SPR TEST + 12V -
ALARM
TAMPER
MW MODULE
J5
EOL TAMPER
J3
EOL ALARM
RED LED
ALARM
GREEN LED
PIR
PIR SETTING
DIPSWITCH
TAMPER
MW SENS.
SETTING
YELLOW LED
MW
(2)
Bend the FILTER
and place in the center
of lens housing
(1)
Remove lens, by pressing
both lens hooks to outside and
pushing the lens to the front.