INSTALLATION INSTRUCTIONS
F W N E O 9 F
FREEWAVE™ WIRELESS PIR WITH PET IMMUNITY UP TO 20 Kg
OPERATION
The Wireless PIR transmits the following events data:
SUPERVISION
- a periodical transmission.
Every 7 min indicates detector’s presence.
ALARM
– alarm transmission triggered by PIR
intrusion detection.
LOW BAT
– Whenever the battery reaches a pre-set
low level (2.4V) Battery Low signal will be sent with the
next message (Supervision, Alarm, etc.
TAMPER
– Whenever the unit cover is removed or the
unit’s cover is put back, a message will be transmitted
with “Tamper” signal.
APS
The unique APS (Automatic Power Saver) function built
in the detector enables a battery life span up to four
years. The detector will transmit only when the last
event has occurred more than 2 minutes prior to the
current one.
PIR SENSITIVITY ADJUSTMENT
Jumper “Sensitivity Adjustment”
use for setting the
PULSE count function in order to provide PIR
sensitivity control according to the environment.
Position Right– “1”-High sensitivity
For stable environments.
Position Left – “2” – Low sensitivity
For harsh environments.
PET IMMUNITY SETTING
Jumper “Pet Immunity Adjustment”
use for setting
the PET Immune function - to 15Kg or 25Kg.
(Depending on the pet weight).
Position Right
Immunity to an animal up to 25 kg
Position Left
Immunity to an animal up to 15 kg
YOU MUST RESET THE DETECTOR BY DISCONNECT
POWER SUPPLY AND RECONNECT IT AFTER FEW
SECONDS.
BATTERY
A 3 V lithium battery powers the unit. Thanks to the
exclusive APS (Automatic Power Saver)
characteristics, the battery provides up to 4 years of
continuous operation (depending on the amount of
alarms).
If the battery reaches a factory preset low level, the
LOW BATTERY signal will be sent and from this
moment the detector remains operational for another
30 days giving enough time to replace the 3V lithium
battery.
BATTERY REPLACEMENT
This action has to be performed by your Service
Personnel.
NOTE:
USE ONLY THE REQUIRED BATTERY AS
SPECIFIED IN "BATTERY" SECTION
Instructions:
•
Remove the front cover.
•
Take out the old battery.
•
Install a new battery according polarity.
•
After assembling the battery the LED will
flash twice in sec for a period of 1 min,
during this time the PIR isn't functioning,
wait until the LED stop flashing.
CAUTION !!!
RISK OF EXPLOSION IF BATTERY
IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE
INSTRUCTIONS.
SUPPLY CONNECTION
The supply connection to the Detectors must only be to a Limited
Power Source (LPS) for the input supply in accordance with the
Standard EN 60950-1 Latest Version
STANDARDS COMPLIANCE
This device complies with:
European Council Directive EMC 89/336/EEC
EN50130-4+A1+A2 EN301489-3
EN300220-3 EN61000-6-3
EN55022 Kl. B
EN50371
EN50131-1 EN50131-5-3
EN50131-2-2 SAFETY
2006/95/EC
EN60950-1
Certified by: ANPI
Security Grade 2, Environmental Class II
For more detailed instruction please refer the manuals which
you could download from the internet at:
www.thecrowgroup.com
The FCC Wants You to Know
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment and receiver.
c) Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected.
d) Consult the dealer or an experienced radio/TV technician.
FCC Warning
Modifications not expressly approved by the manufacturer could
void the user authority to operate the
equipment under FCC Rules.
Ceiling bracket base
Wall bracket base
Fig.4
TECHNICAL SPECIFICATION
Modulation Type
2FSK (1 Frequency)
Frequency band
916.5MHz
Identification
Unique ID serial number –
24bit
Event Transmission
Alarm, Tamper, Test,
Supervision, Low Bat
Supervision Timing
Every7 minutes (randomly)
Detection Method
Dual Element PIR
Lens Type
Hard Lens
Range in open space up to 300 m
Environment Condition Jumper for Normal or Harsh
selection
RF Immunity
10 V/m Pulse and 80% AM
from 80 MHz to 2GHz
Battery
Lithium. 3V Type: xx123 Size:
2/3AA
Current Consumption
Standby ~10
μ
A
Transmission ~24
mA
Power Saving
APS (Automatic Power Saver)
Installer Test Modes LED Indicator (RF & Optic)
Walk test &
Alarm transmission test
Operating temperature
Range -10
°
C to +50
°
C
Dimensions 123mm x 62mm x 38mm
Weight
120gr
Standards
FCC Part 15 and ETS 300-
220
CROW ELECTRONIC ENGINEERING LTD. ("Crow") - WARRANTY POLICY CERTIFICATE
This Warranty Certificate is given in favor of the purchaser (hereunder the "
Purchaser
") purchasing the products directly from Crow or from its authorized distributor.
Crow warrants these products to be free from defects in materials and workmanship under normal use and service for a period of 24 months from the last day of the week and
year whose numbers are printed on the printed circuit board inside these products (hereunder the "
Warranty Period
").
Subject to the provisions of this Warranty Certificate, during the Warranty Period, Crow undertakes, at its sole discretion and subject to Crow's procedures, as such procedures
are form time to time, to repair or replace, free of charge for materials and/or labor, products proved to be defective in materials or workmanship under normal use and service.
Repaired products shall be warranted for the remainder of the original Warranty Period.
All transportation costs and in-transit risk of loss or damage related, directly or indirectly, to products returned to Crow for repair or replacement shall be borne solely by the
Purchaser.
Crow's warranty under this Warranty Certificate does not cover products that is defective (or shall become defective) due to: (a) alteration of the products (or any part thereof)
by anyone other than Crow; (b) accident, abuse, negligence, or improper maintenance; (c) failure caused by a product which Crow did not provide; (d) failure caused by
software or hardware which Crow did not provide; (e) use or storage other than in accordance with Crow’s specified operating and storage instructions.
There are no warranties, expressed or implied, of merchantability or fitness of the products for a particular purpose or otherwise, which extend beyond the description on the
face hereof.
This limited Warranty Certificate is the Purchaser's sole and exclusive remedy against Crow and Crow's sole and exclusive liability toward the Purchaser in connection with the
products, including without limitation - for defects or malfunctions of the products. This Warranty Certificate replaces all other warranties and liabilities, whether oral, written,
(non-mandatory) statutory, contractual, in tort or otherwise.
In no case shall Crow be liable to anyone for any consequential or incidental damages (inclusive of loss of profit, and whether occasioned by negligence of the Crow or any
third party on its behalf) for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever. Crow does not represent that these
products can not be compromised or circumvented; that these products will prevent any person injury or property loss or damage by burglary, robbery, fire or otherwise; or that
these products will in all cases provide adequate warning or protection.
Purchaser understands that a properly installed and maintained product may in some cases reduce the risk of burglary, fire, robbery or other events occurring without providing
an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss or damage as a result.
Consequently, Crow shall have no liability for any personal injury; property damage or any other loss based on claim that these products failed to give any warning.
If Crow is held liable, whether directly or indirectly, for any loss or damage with regards to these products, regardless of cause or origin, Crow’s maximum liability shall not in
any case exceed the purchase price of these products, which shall be the complete and exclusive remedy against Crow.
CROW ELECTRONIC ENGINEERING LTD.
ISRAEL
:
Crow Electronic Engineering Ltd.
12 Kineret St. Airport City
P.O. Box 293 Ben Gurion Airport , 70100
Tel:
972-3-9726000
Fax:
972-3-9726001
E-mail:
USA
:
2160 North Central Road,
Fort Lee, N.J. 07024
Tel: 1-800-GET CROW
or (201) 944 0005
Fax: (201) 944 1199
E-mail:
AUSTRALIA
:
429 Nepean HWY Brighton East Vic 3187
Tel: 61-3-9596 7222
Fax: 61-3-9596 0888
E-mail:
POLAND:
VIDICON SP. ZO. O.
15 Povazkowska St.
01 – 797 Warsaw Poland
Tel: 48 22 562 3000
Fax: 48 22 562 3030
E-mail:
LATIN AMERICA:
CROW LATIN AMERICA
5753
NW
151
ST
.Street
MIAMI
LAKES,
FL 33014 – USA
Tel: +1-305-823-8700
Fax:
+1-305-823-8711
E-mail:
ITALY
:
DEATRONIC
VIA Giulianello 4/14
00178
ROMA,
ITALY
Tel: +39-0676-12912
Fax: +39-0676-12601
E-mail:
These instructions supersede all previous issues in circulation prior to January
2006.
7101799_A
- 2 -
N345
The battery must be replaced
by Size 2/3 CR 17345
Lithium battery 3V
Models as: Power One CR123A-6205
The battery model be only to a type considered a "Limited
Power Source" (LPS
)
in accordance with the Standard EN
60950-1 Latest Version
