background image

7

Radio Operation

Radio Operation

1

Press the FM BUTTON (5) or the AM BUTTON
(6) to select the desired radio band.

2

Turn the TUNING KNOB (7) to set the desired
station.

3

Adjust the volume to the desired level.

4

Adjust the VOLUME KNOB (3) to the desired
sound level.

1

 You can connect your radio to different sources
using the auxiliary outputs.

2

Connect the auxiliary cables to the LINE OUT
JACK (8) to the auxiliary inputs on the desired
component. See the owner’s manual for the
operating instructions for the desired component.
The LINE OUT JACK (8) only puts out a signal
and will not run external speakers without using
a  separate amplified source.

Auxiliary Outputs

Antenna: for FM reception, the unit is provided with
a FM WIRE ANTENNA (10) , move the wire until
the reception is clear and with no interferences. For
AM reception, the unit is provided with a directional
build-in ferrite antenna. Rotate the set to find the
position in which the best reception is obtained. Do
not connect the FM WIRE ANTENNA (10) to any
outside antenna.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

The lighting flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert user to
the presence of uninsulated
"dangerous voltage" within
the product's enclosure
that may be of sufficient
magnitude to constitute
risk of electric shock
to persons.

CAUTION: TO REDUCE
THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE
COVER (OR BACK). NO
USER - SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.

CAUTION

For Compact Disc Units Only:
INVISBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED
OR DEFEATED. AVOID DIRECT EXPORSURE TO LASER BEAM.

Specification

Frequency Range

:  AM 525 - 1710 KHz
:  FM 87.5 - 108.5 MHz

Power Consumption

: 17 Watts

Antennas

:  External FM antenna
: Built-in ferrite AM bar

Power Source

:  AC 120V ~ 60 Hz

Speaker

:  4” Dynamic type X 2

Speaker Wattage

: 5 Watts

Speaker ohms

: 4 ohms

Output ohms

: 4 ohms

Output Wattage

: 2 Watts per channel

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

* DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT  NOTICE.

The exclamation point
within an equilateral
triangle is intended to
alert user to the
presence of important
operating and
maintenance (servicing)
instruction in the
literature accompanying
the appliance.

Antenna

Summary of Contents for CR711







Reviews: