background image

 

OPERATING INSTRUCTIONS 

 

REMOTE PANIC PROTECTION 

To  sound  the  alarm  upon  command  (panic),  press  and  hold  the  Panic  Button  for  at  least  2  seconds  until  the 
siren sounds.  Press the Unlock Button to reset panic mode. 

 
IGNITION-CONTROLLED DOOR LOCKS: (Programmable Option # 13) 

The doors  will  automatically lock when the ignition is turned on and  will unlock when  the ignition is turned  off.  
This feature can be programmed on, off, or to lock the doors only. 

Doors will not lock if they are open to prevent 

locking the keys in. 

 

SENSOR BYPASS THRU REMOTE CONTROL 

The shock sensor circuit can be bypassed thru the remote control by pressing the Lock and Unlock button 
within 4 seconds of arming the system. The Siren Chirp 3 times to confirm sensor bypass. 
 

ARM / DISARM WITH IGNITION ON: (Programmable Option # 15) 

This  feature  allows  the  system  to  be  armed  or  disarmed  while  the  ignition  is  in  the  ON  position  or  vehicle  is 
running.  The feature is disabled by default and should not be used under normal operating conditions.  On an 
installation with an add-on remote start module, this option can be enabled to allow the system to be armed or 
disarmed when the vehicle has been remote started (Ignition will be ON).  Note that you cannot use this feature 
if  you  are  also  using  the  Full-time  carjack  protection.    If  you  add  a  remote  start  and  the  Ignition  turns  on,  a 
Carjack trigger will be activated. 

 
ACTIVE REARM / AUTO REARM: (Option # 6)

 

The option controls whether the alarm system rearms 30 seconds after disarm. This is required for insurance 
discounts. This is handy if the vehicle is accidentally disarmed without your knowledge. There are 4 choices: 

1. 

Active Rearm ON – The system will Rearm and lock the doors unless the door, hood or trunk is opened.

 

2. 

OFF = Default

 - No Automatic Rearm in Passive or Active Mode.

 

3. 

Auto Rearm with Lock - The alarm system will always rearm and lock the doors after disarm unless the 
ignition is turned on. This applies to Passive and Active Mode. This choice is best for security but 
increases the risk of locking the keys in the ignition.

 

4. 

Auto Rearm without Lock - The alarm system will always rearm without locking the doors after disarm 
unless the ignition is turned on. This applies to Passive and Active Mode.

 

Summary of Contents for SP-202

















Reviews: