background image

 

EZ-45DP/55DP 1 WAY SYSTEMS

 

EZ-95FM 2-WAY SYSTEM 

DP SERIES (Data port)

 

 

REMOTE ENGINE STARTING SYSTEM 

 

INSTALLATION INSTRUCTIONS 

 
 

INTRODUCTION 

 

CONGRATULATIONS

 on your choice of a “Cool Start” System by Crimestopper Security Products Inc.  This booklet 

contains the information necessary for installing your remote starter system.  If any questions arise, contact your 
installation dealer or Crimestopper Security Products Inc. at the Tech Support number below. 

 
DISCLAIMER: 
This installation book is designed for the installer or individual with an existing understanding of automotive electrical 
systems, along with the ability to test and connect wires for proper operation.  To ease installation, we suggest that you 
READ THIS MANUAL before beginning your installation.  This book is provided as a GENERAL GUIDELINE and the 
information contained herein may differ from your vehicle.  Crimestopper Security Products, Inc. and its’ vendors shall not 
be liable for any accident resulting from the use of this product.  This system is designed to be professionally installed into 
a vehicle in which all systems and associated components are in perfect working condition. 

 
 

TECHNICAL SUPPORT: (800) 998-6880 

Monday - Friday 8:00am - 4:30pm Pacific Std. Time 
Web Site: www.crimestopper.com 
E-mail: [email protected] 

 

CRIMESTOPPER SECURITY PRODUCTS, INC. 
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063 

 

REV A  10.19.2005 
 
 

This device complies with FCC Rules part 15.  Operation is subject to 
the following two conditions:  (1) This device may not cause harmful 
interference, and (2) This device must accept any interference that 
may be received, including interference that may cause undesired 
operation.  The manufacturer is not responsible for any radio or TV 
interference caused by unauthorized modifications to this equipment. 
 Such modification could void the user’s authority to use the 
equipment. 

Summary of Contents for EZEE Start EZ-45DP

































Reviews: