background image

 
 
 
 

REMOTE ENGINE CONTROL 

 

ENTERING YOUR REMOTE STARTED VEHICLE: 

1)  With engine running, Remote Unlock system or open door with key. 
2)  Enter vehicle and be careful not to step on brake pedal!  (Remote Start Reset) 
3)  Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park. 
4)  Remote starter will reset instantly when the brake is pressed.  Parking lights will turn off and the ignition key is 

now controlling your vehicle. 

 
 
 

IDLE DOWN MODE: 

This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you 
exit the vehicle.  The vehicle is put into a remote running condition before you exit and it will remain running for the 
programmed run time or until you come back. Example: You pull up to a convenience store for a quick stop, "Idle 
Down" mode keeps engine running when you exit the vehicle, (with keys in hand) remote lock doors. When you 
return, unlock, turn ignition ON and drive away. 

 

IDLE DOWN MODE - EXITING THE VEHICLE: 

1)  With vehicle engine running with key, press the Remote Start button for at least 1 second. 
2)  Parking Lights will turn ON. 
3)  Doors will unlock, or if brake pedal is being depressed, doors will unlock when it is released. 
4)  Turn OFF Ignition and remove key.  Engine should remain running. 
5)  Exit vehicle then remote lock doors if desired. 
6)  Engine will remain running for programmed run time or until you return (whichever comes first). 

 

IGN

SOLID

OFF

UNLOCK

 

 
 
 

Summary of Contents for Cool Start RS-840













Reviews: