background image

 

TURBO TIMER MODE (OPTIONAL) 

 

The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running for 1 
to 5 minutes [selectively] after you remove the key, exit the vehicle, and lock the doors remotely.  This is handy for 
turbo cool-down without the need for expensive turbo timers.  This mode requires the use of an extra part called a 
momentary switch/button that is not included with the kit.  Check with your installer about adding this feature.   

NOTE:  The turbo timer button will also trigger a remote start if it is inadvertently pressed when the vehicle is not 
running.  Please note this when installing the button and choose a location out of harm’s way.  

 

1)  Engine should be running with the key. 
2)  Press and hold down the brake pedal. 
3)  Press your “Turbo Timer” button 1 to 5 times for each minute of run time you desire. (1 press = 1 min.) 
4)  As you release the brake pedal and your system will confirm by flashing the lights the same number of times the 

button was pressed. 

5)  Turn Ignition switch OFF, remove key and exit the vehicle.  Remote lock your doors for safety.  The engine 

should remain running for the selected number of minutes. 

REMOVE KEY

PRESS TURBO

FLASH 1-5X

EXIT VEH.

PRESS

AND HOLD

BRAKE

TIMER BUTTON

1-5 TIMES

RUNNING

RELEASE

BRAKE

LIGHTS

RUNNING

REMAIN

1-5 MIN.

 

Summary of Contents for Cool Start RS-1300DP

















Reviews: