Change the Default Scenes
The Zūm keypad buttons recall predefined scenes (light levels) that are stored in the
load controllers. The default scenes are ON (scene 1) which sets the loads at 90%,
SCENE 2 which sets the loads at 50%, and SCENE 3 which sets the loads at 10%.
Load controllers can save up to 16 scenes.
There are several methods of changing the default scenes, use the method that
matches your needs.
• End-User Method - Change the light levels for SCENE 2 or SCENE 3 on a
ZUMMESH-KP10B when all load controllers are easily accessible.
• Manual Method - Change the light levels for ON (scene 1) on a
ZUMMESH-KP10A or ZUMMESH-KP10B when all load controllers are easily
accessible. Additionally, SCENE 2 and SCENE 3 light levels can be changed on a
ZUMMESH-KP10B.
• Remote Method - Change the light levels for ON (scene 1), SCENE 2, or
SCENE 3 on a ZUMMESH-KP10A or ZUMMESH-KP10B when a load controller is
not physically accessible.
NOTE:
A dimmer lowered to 0% will turn the dimmer off when the scene is
recalled.
NOTE:
A load controller that is not bound to the keypad cannot be part of the
scene.
End-User Method:
1. Set all load controllers that are bound to the keypad to their desired light level.
2. Press and hold the
SCENE 2
or
SCENE 3
button on the keypad until the LED
lights (about 5 seconds). The light levels are saved to the pressed button.
Manual Method:
NOTE:
Scene 2 and Scene 3 can also be changed.
1. Enter Scene Setting Mode using the keypad that will recall the scene.
a. Press and hold both the top and bottom buttons until the LED lights (about
5 seconds).
b. Press the top button two times.
c. Press the bottom button once. The LED on the keypad flashes its LED two
times every two seconds to indicate that it is in Scene Setting mode. Load
controllers that are bound to the keypad flash their LED rapidly.
Press and hold until LED lights
Press and hold until LED lights
then
then
Press 2x
Press 1x
NOTE:
Scene Setting Mode exits after 5 minutes when initiated from an ac-
powered keypad or 1 minute when initiated from a battery powered keypad.
2. Adjust all light levels.
• Using a dimmer, press and hold the top button to raise the light level or press
and hold the bottom button to lower the light level.
• Using a switch, press the top button to turn the lights on or press the bottom
button to turn the lights off.
• Using a J-box load controller, press and hold the
TEST
button on the J-box
device to cycle-dim the light.
3. Using the keypad that initiated Scene Setting mode, press the
ON
,
SCENE 2
, or
SCENE 3
button to save the light levels to the selected scene button.
4. Repeat steps 2 and 3 for each scene button.
5. Press the bottom button on the keypad 3 times to exit.
Press 3x
Remote Method:
1. Enter Scene Setting Mode using the keypad that will recall the scene.
a. Press and hold both the top and bottom buttons until the LED lights (about
5 seconds).
b. Press the top button two times.
c. Press the bottom button once. The LED on the keypad flashes its LED two
times every two seconds. Load controllers that are bound to the keypad flash
their LED rapidly.
Press and hold until LED lights
Press and hold until LED lights
then
then
Press 2x
Press 1x
NOTE:
Scene Setting Mode exits after 5 minutes when initiated from an ac-
powered keypad or 1 minute when initiated from a battery powered keypad.
2. Press and hold the bottom button of the keypad until a set of lights in the space
flashes on and off twice (about 3 seconds) to indicate that it is selected load. The
lights return to their previous level.
Press and hold 3 sec.
3. Press the bottom button of the keypad to cycle through all of the load controllers
in the Zūm space until the desired load starts flashing.
Press 1x
4. Adjust the light levels by holding the top button on the keypad to raise the light
level or holding the bottom button on the keypad to lower the light level.
5. Press the
ON
,
SCENE 2
, or
SCENE 3
button to save the scene.
6. Repeat steps 3 through 5 until all load controllers and all scenes are defined.
7. Press the bottom button on the keypad 3 times to exit.
Press 3x
Factory Reset
Perform a factory reset when the device is removed from the network or to remove
the configuration settings. The device must also be factory reset if the device is being
moved to a different system.
NOTE:
New-in-box devices do not need to be factory reset before joining a system.
To factory reset the ZUMMESH-KP:
1. Press and hold the top and bottom buttons until the LED lights (about 5 seconds).
2. Press and hold the bottom button until the LED lights (about 10 seconds).
Press and hold until LED lights
Press and hold until LED lights
Press and hold until LED lights
then
Specifications
The specifications for the keypad are listed below.
SPECIFICATION
DETAILS
Power Requirements
100-277 VAC, 50/60 Hz
Enclosure
1-gang mountable in a 3-1/2 in deep electrical box;
Requires decorator-style faceplate (not included)
Environmental
Temperature
Humidity
32° to 104 °F (0° to 40 °C)
10% to 90% RH (noncondensing)
Dimensions
Height
Width
Depth
4.13 in (105 mm)
1.75 in (45 mm)
1.8 in (46 mm)
Weight
5 oz (142 g)
This product is Listed to applicable UL
®
Standards and requirements tested by Underwriters
Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters
Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own
expense.
Industry Canada (IC) Compliance Statement
CAN ICES-3(A)/NMB-3(A)
The product warranty can be found at
www.crestron.com/warranty
.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents
.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/opensource
.
Crestron, the Crestron logo,and Zūm are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either
trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States
and/or other countries. Other trademarks, registered trademarks, and trade names may be used
in this document to refer to either the entities claiming the marks and names or their products.
Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not
responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.
Crestron Electronics, Inc.
Installation Guide - DOC. 7956B
15 Volvo Drive, Rockleigh, NJ 07647
(2047775)
Tel: 888.CRESTRON
05.18
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.
