background image

Crestron 

WPR-48 

Waterproof Wireless Handheld Remote

 

PRO2 System View 

 

The 

System Views

 

lower pane displays the PRO2 system tree. This tree can be 

expanded to display and configure the communications ports.

 

Expanded PRO2 System Tree 

 

C2Net-Device Slot in Configuration Manager 

An RF gateway device is required to incorporate a wireless RF transmitter into a 
Cresnet system. Once a gateway is configured in a C2Net-Device Slot, the slot 
allows Cresnet communication between the transmitter and the control system. 
Similarly, an IR gateway device or receiver is required to incorporate a wireless IR 
transmitter into a Cresnet system. 

To incorporate the RF configuration of the WPR-48 in a SIMPL program, in 
Configuration Manager, drag the CNRFGWA RF gateway from the Wireless 
Receivers | Wireless Receivers (RF) folder of the 

Device Library

. The 

System Views

 

upper pane displays the CNRFGWA device icon below the PRO2 graphic. The 
PRO2 system tree displays the CNRFGWA gateway in Slot 9, with a default Net ID 
of 24. 

NOTE:

  The ST-CP control processor is automatically configured with a 

CNRFGWA in its STCP-Net Device Slot 3, with a fixed Net ID of 2, when the  
ST-CP is dragged into the upper pane of 

System Views

. This Net ID cannot be 

changed. 

To incorporate the IR configuration of the WPR-48 in a SIMPL program, in 
Configuration Manager, drag the CNX-RMC or CNX-RMCLV room solution box 
from the Cresnet Control Modules | Cresnet Video Modules folder of the 

Device 

Library.

 The 

System Views

 upper pane displays the CNX-RMC device icon below 

the PRO2 graphic. Then drag the CNXRMIRD IR detector from the Wireless 
Receivers | Wireless Receivers (IR) folder of the

 Device Library

 and drop it on the 

CNX-RMC

The PRO2 system tree displays the CNXRMIRD IR detector in Slot 2 

of the CNX-RMC. 

Double-click the CNRFGWA or the CNX-RMC icon in the lower pane to open the 
“Device Settings” window, which displays device information. Select the 

Net ID

 tab 

to change the gateway Net ID. The window for the CNRFGWA is shown in the 
following figure.  

Operations Guide – DOC. 6254A 

Waterproof Wireless Handheld Remote: WPR-48  

  15 

Summary of Contents for WPR-48





























Reviews: